Inserting The Battery; Replacing The Battery - Hama PP-245 Instrucciones De Uso

G Operating instruction
Controls and Displays
1. AM/PM (12-hour format)
2. Time
3. Day
4. Month
5. Day of the week
6. Moon phase
7. Room temperature
8. Time zone
9. Summer time
10. Battery symbol
11. Wireless symbol
12. Opening for wall mounting
13. Base
14. MODE button
= settings/con rms the setting
15. °F/°C button
= switches between °C and °F
16. UP button
= increases the current setting; activates/deactivates manual radio signal
reception; switches the display mode
17. DOWN button
= decreases the current setting; activates/deactivates manual radio signal
reception; selects the language
18. Battery compartment
Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely.
Please keep these instructions in a safe place for future reference. If you sell the
device, please pass these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your
attention to speci c hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package Contents
• PP-245 DCF wireless wall clock
• 1 AA battery
• These operating instructions
3. Safety Instructions
• The product is intended for private, non-commercial use only.
• Use the product for its intended purpose only.
• Protect the product from dirt, moisture and overheating, and only use it in a dry
environment.
• Do not operate the product outside the power limits given in the speci cations.
• Do not use the product in moist environments and avoid splashes.
• Do not use the product in the immediate vicinity of heaters or other heat sources
or in direct sunlight.
• Do not use the product in areas where the use of electronic devices is not permitted.
• Do not place the product near interference elds, metal frames, computers, TVs,
etc. Electronic devices and window frames can negatively affect the product's
functionality.
• Do not drop the product and do not expose it to any major shocksl.
• Do not open the device or continue to operate it if it becomes damaged.
• Do not attempt to service or repair the product yourself. Leave any and all service
work to quali ed experts.
• Keep the packaging material out of the reach of children due to the risk of
suffocation.
• Dispose of packaging material immediately according to locally applicable
regulations.
• Do not modify the product in any way. Doing so voids the warranty.
2
Warning – Batteries
• When inserting batteries, note the correct polarity (+ and - markings) and
insert the batteries accordingly. Failure to do so could result in the batteries
leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the speci ed type.
• Before you insert the batteries, clean the battery contacts and the polar
contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries or batteries of a different type or make.
• Remove the batteries from products that are not being used for an extended
period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a re.
• Keep batteries out of the reach of children.
• Never open, damage or swallow batteries or allow them to enter the
environment. They can contain toxic, environmentally harmful heavy metals.
• Immediately remove and dispose of dead batteries from the product.
• Avoid storing, charging or using batteries in extreme temperatures.
4. Getting Started

4.1 Inserting the battery

Remove the battery that was already inserted into the clock, remove the protective
lm if necessary as well as the contact interrupter and the re-insert the battery with
the correct polarity. The clock is ready for operation.

4.2 Replacing the battery

Remove and dispose of any used batteries. Insert the new battery (AA). Ensure that the
polarity of the battery corresponds to the symbols in the battery compartment (18).
5. Installation
Warning – Mounting Note
• Before mounting the clock, ensure that the chosen wall is suitable for
the weight to be mounted, and make sure that there are no electrical
wires, water, gas or other lines at the installation site on the wall.
• Purchase special fastening materials from specialised dealers.
• Do not mount the product above locations where persons might linger.
• You can mount the wall clock on a wall using the opening on the back (12).
• You can also stand the wall clock on a level surface using the base (13).
6. Operation
Note – Input
Hold down the UP button (16) or the DOWN button (17) to select the
values faster.
6.1. Automatic setting using the DCF signal
• Once the batteries are inserted, the clock automatically searches for a DCF signal.
During the search, the wireless icon (11) ashes.
Display
Display ashing
Displayed continuously
Not displayed
• If the station still does not receive a signal, press and hold the UP button (16) and
the DOWN button (17) for approx. 3 seconds to start the manual search for the
DCF signal. The wireless icon (11) will start to ash.
Searching for the DCF signal
Active
Successful – signal is being
received
Deactivated