Pioneer Elite FS-EB70 Manual De Instrucciones página 56

> Before Start > Part Names
The subwoofer produces no sound
0 Make sure that the power cord of the subwoofer is
properly plugged into the wall outlet.
0 Check that the subwoofer LINK LED is illuminated. If it is
blinking, follow the below procedure to pair the main unit
and the subwoofer.
1.Press and hold LINK on the rear panel of the
subwoofer until the blinking speed of LINK LED
changes.
2.While pressing VOLUME – on the front of the main
unit, press DIMMER on the front of the main unit.
"Pairing" is displayed on the main unit display.
3.When "Paired" is displayed on the main unit display
and LINK LED on the subwoofer lights, pairing is
complete.
0 Sound may jump or stop depending on reception. Move
the subwoofer closer to the main unit if you notice this. If
there are obstacles in the way, try moving them.
0 When you play source material that contains no
information in the LFE channel, the subwoofer produces
no sound.
Noise can be heard
0 Using cable ties to bundle RCA cables with power cords,
sound bar connection cable, etc. may degrade the audio
performance, so refrain from doing it.
0 An audio cable may be picking up interference. Try
repositioning your cables.
The beginning of audio received via HDMI cannot be
heard
0 Since it takes longer to identify the format of an HDMI
signal than it does for other digital audio signals, audio
output may not start immediately.
Sound suddenly reduces
0 When the temperature inside the main unit exceeds a
certain temperature for extended periods, the volume
may be reduced automatically to protect the circuits.
56
> Install > Initial Setup
■ Listening Modes
0 To enjoy digital surround playback, such as Dolby Digital,
the audio signals need to pass through a connection via
HDMI cable or digital optical cable. Audio output should
be set to bitstream output on the connected Blu-ray Disc
player or other device.
0 Press on the remote controller several times to switch
the display of this unit to check the input format.
Check the following if the above does not fix the problem:
Cannot select a desired listening mode
0 Depending on the connecting status of the speaker,
some listening modes may not be selected. (
There is no sound with Dolby TrueHD, Dolby Atmos,
DTS-HD Master Audio and DTS:X.
0 If you cannot output formats such as Dolby TrueHD,
Dolby Atmos, DTS-HD Master Audio or DTS:X according
to the format of the source, in the Blu-ray Disc player
settings try setting "BD video supplementary sound" (or
re-encode, secondary sound, video additional audio,
etc.) to "Off". Change the listening mode for each source
after changing the setting to confirm.
About DTS signals
0 With media that switches suddenly from DTS to PCM,
PCM playback may not start immediately. In such cases,
you should stop your player for about 3 seconds and then
resume playback.
0 With some CD and LD players, you will not be able to
playback DTS material properly even though your player
is connected to a digital input on the unit. This is usually
because the DTS bitstream has been processed (e.g.,
output level, sampling rate, or frequency response
changed) and the unit does not recognize it as a genuine
DTS signal. In such cases, you may hear noise.
0 Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
> Playback
Advanced Setup | Firmware Update |
produce a short audible noise. This is not a malfunction.
■ Video
0 Confirm that the connection between the output jack on
the device and the input jack on this unit is correct.
0 Make sure that none of the connecting cables are bent,
twisted, or damaged.
0 When the TV image is blurry or unclear, power code or
connection cables of the unit may have interfered. In that
case, keep distance between TV antenna cable and
cables of the unit.
0 Make sure the switching of input screens is proper at the
P30)
monitor side such as a TV.
Check the following if the above does not fix the problem:
There is no video
0 Change the input selector on this unit to the position of
the terminal to which the player is connected.
There is no picture from a source connected to an HDMI
IN terminal
0 To display video from the connected player on the TV
while the unit is in standby, you need to enable "System
Setup" - "Hardware" - "HDMI" - "HDMI Standby Through"
in the Home. Refer to (
HDMI Standby Through.
0 Check if "Resolution Error" is displayed on this unit's
display when video input via HDMI IN jack is not
displayed. In this case, the TV does not support the
resolution of the video input from the player. Change the
setting on the player.
0 Reliable operation with an HDMI-to-DVI adapter is not
guaranteed. In addition, video signals from a PC are not
supported.
Others
E
N
P45) for information about