For Blowing - Makita DVC750L Manual De Instrucciones

Carriage handle
When carrying the cleaner, carry it by holding the handle on the
head. The handle is retractable at the head when not in use.
► Fig.6
NOTE: When water is in the tank, switch off the
cleaner and empty the tank before carrying. The
water inside may leak.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Connecting the hose
NOTICE:
Never force the hose for bending or
stamp it. Never move the cleaner by a hose.
Forcing, stamping and pulling the hose may cause a
breakage or deformation of the hose.
NOTICE:
Do not pick up large wastes such as
planer carvings and concrete pieces. It may cause
a hose stuffing and damage.
For vacuum cleaning
Insert the hose into the suction inlet and turn it clock-
wise until it clicks.
► Fig.7: 1. Suction inlet

For blowing

Insert the hose to blower outlet and turn it clockwise
until it clicks.
► Fig.8: 1. Blower outlet
NOTE: This cleaner has the suction inlet and blower
outlet separately. Connect the hose to the proper port
depending on your work.
Connecting the nozzle
Attach the wide nozzle, sash nozzle, or other nozzles sup-
plied as optional accessories depending on your purpose.
To attach the nozzle, twist and insert it to the end of the hose.
► Fig.9
Connecting the tool
Optional accessory
To connect the tool, connect the end of the hose to the
tool's extraction outlet. Depending on the tool, you may
need the optional joint 22-38 or the front cuff 24.
► Fig.10: 1. Hose 2. Joint 22-38 3. Front cuff 24
NOTE: When connecting the tool, always make sure that
the hose is connected to the suction inlet on the cleaner.
Storage of hose and nozzles
The hose and nozzles can be stored on the tool as
illustrated.
► Fig.11: 1. Sash nozzle 2. Wide nozzle
When storing the hose, loop it on the tool and fix it with
the hook as illustrated.
► Fig.12: 1. Hose 2. Hook
Installing the shoulder strap
Optional accessory
Attach the hooks of the shoulder strap onto the mounts
of the cleaner as shown in the figure.
► Fig.13: 1. Shoulder strap 2. Hook 3. Mount
OPERATION
Using as a vacuum cleaner
NOTICE:
Be sure to dry the HEPA filter after pick-
ing up water or wet dust. If you use the wet filter, the
suction power may be reduced.
1.
Install the hose and nozzle onto the suction inlet
and turn on the tool.
2. After vacuum cleaning, empty the tank before it
becomes full.
► Fig.14
Using as a blower
CAUTION:
Do not blow out muddy water such
as pool and sand area. If foreign objects are blown
into eyes, it may result in personal injury.
CAUTION:
Do not operate as a blower against
the wind. If foreign objects are blown into eyes, it
may result in personal injury.
CAUTION:
Always use protective goggles, a
cap and mask while operating.
CAUTION:
Never point the nozzle at anyone
in the vicinity.
CAUTION:
The operator or user is responsi-
ble for accidents or hazards occurring to other
people or their property.
CAUTION:
Do not use the tool for blowing
air into objects, like rubber rafting, balls or other
inflatable products. Increased motor revolution may
cause dangerous fan breakage.
1. Install the hose into the blower outlet.
2. Point the hose tip to the object to be blown off and
turn on the tool.
► Fig.15
NOTE: To clean narrow space, connecting the sash
nozzle to the hose makes it easy.
11 ENGLISH