Software Update; Switching Bicycle Lights On/Off - Bosch PowerPack 300 BBS245A Manual Del Operador

Inserting the univer- Push the universal holder (16) onto
sal holder the SmartphoneHub from the front
(see figure A)
until you hear it click into place ➊. The
universal holder can also be fixed in
place using the two fastening
screws (17).
Inserting the smart- – Pull the front mounting
phone bracket (18) forwards ➋.
(see figure B)
– Insert the smartphone with the long
side of the phone positioned
against the rear mounting
bracket (19) ➌.
– Allow the front mounting
bracket (18) to slide slowly to-
wards the smartphone and release
it ➍.
Power supply for The smartphone can be supplied with
the smartphone power (5 V/1 A) using a separate USB
(optional) cable (included with delivery) via the
micro-A/B USB port of the Smart-
phoneHub. To do this, connect the
smartphone to the USB port of the
SmartphoneHub using the USB cable.
Removing the Use both hands to push the smart-
smartphone phone forwards along with the front
mounting bracket until the smart-
phone can be removed from the uni-
versal holder. If necessary, remove
the USB cable for the power supply.

Software update

If a software update is available for the SmartphoneHub, an
indicator is shown in the smartphone app. Follow the in-
structions in the app to perform the update.
Recovering the SmartphoneHub
A recovery operation should be carried out on the Smart-
phoneHub if it is no longer functioning correctly. To do this,
open the app on your smartphone and follow the instruc-
tions.
Power supply for the SmartphoneHub
The SmartphoneHub has an internal lithium-ion polymer bat-
tery (nominal/minimum 300 mAh, 3.7 V) that cannot be re-
moved.
The SmartphoneHub can be switched on via its on/off but-
ton (2) or via the on/off button of the eBike battery. If the
SmartphoneHub cannot be switched on, it must be charged
via a USB cable for at least 30 minutes.
Switching the push assistance on/off
The push assistance aids you when pushing your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of 6 km/h. The lower the selected gear,
the lower the speed of the push assistance function (at full
power).
Bosch eBike Systems
The push assistance function must only be used when
u
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To activate the push assistance, briefly press the WALK
button on your operating unit. Once it is activated, press and
hold the + button within three seconds. The eBike drive is
now switched on.
Note: The push assistance cannot be activated at assistance
level OFF.
The push assistance is switched off as soon as one of the
following occurs:
– You release the + button;
– The wheels of the eBike are locked (e.g. by applying the
brakes or hitting an obstacle);
– The speed exceeds 6 km/h.
The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.
Setting the assistance level
On the operating unit (15), you can set the level of assist-
ance you want the eBike drive to provide you with while ped-
alling. The assistance level can be changed at any time, even
while cycling.
Note: In some models, the assistance level may be preset
and cannot be changed. There may also be fewer assistance
levels available than stated here.
The following assistance levels are available as a maximum:
– OFF: Motor assistance is switched off. The eBike can just
be moved by pedalling, as with a normal bicycle. The
push assistance cannot be activated at this assistance
level.
– ECO: Effective assistance with maximum efficiency, for
maximum range
– TOUR: Steady assistance, long range for touring
– SPORT/eMTB:
SPORT: Powerful assistance, for mountain biking and
cycling in urban traffic
eMTB: Optimum assistance whatever the terrain, rapid
acceleration when starting from a standstill, improved dy-
namics and top performance (eMTB only available in
combination with the drive units BDU250P CX, BDU365,
BDU450 CX and BDU480 CX. A software update may be
required.)
– TURBO: Maximum assistance even at high pedalling
speeds, for sport cycling
To increase the assistance level, press the + (14) button on
the operating unit repeatedly until the desired assistance
level appears on the display. To decrease the assistance
level, press the – (11) button.

Switching bicycle lights on/off

On the model in which the lighting is powered by the eBike
system, the front and rear lights can be switched on and off
English – ​ 3
EN-65
1 270 020 XBC | (08.04.2019)