Automatic Operation - Audio-Technica AT-LP60-BT Instalación Y Funcionamiento

Connecting to Stereo System (Wireless Connection)
About Pairing
To connect the turntable to a Bluetooth receiver device, the turntable
needs to pair (register) with the device. Once it is paired, you will not
need to pair it again with that device, except in the following cases:
• If the turntable is deleted from the Bluetooth receiver device
connection history,
• If the turntable is sent out for repair,
• If the turntable is paired with 5 devices or more,
(The turntable can be paired with up to 4 devices. When you pair
with a new device after pairing with 4 devices, pairing information
for the device with the oldest connection date will be overwritten by
information for the new device.)
How to Perform Pairing
* Read the user manual for the Bluetooth receiver device.
* Place the Bluetooth receiver device within 1 meter of the turntable to
perform pairing correctly.
1. Set your Bluetooth headphones, speakers, etc. to pairing mode.
2. Press and hold the wireless function button. After two seconds,
the wireless function button flashes three times in purple.
Continue to press and hold the wireless function button until the
wireless function button flashes once in purple, then release
(total cycle is five seconds). The wireless function button flashes
in red and blue to indicate pairing mode. Please wait.
Press and hold for
about 5 seconds
P P P
(flashes three times (flashes once
in Purple) in Purple)
3. When pairing is complete, the wireless function button lights
in blue.
NOTE: The product stays in the pairing mode for 30 seconds. If pairing
is not properly completed, follow the above steps again from the
beginning.
Operation

Automatic Operation

1. Remove the stylus guard from the stylus assembly
(Fig. 4).
2. Put a record on the turntable. If needed, use the
45 RPM adapter (Fig. 5).
3. Select the size of record: 12" or 7" (Fig. 6).
4. Select the speed: 33 / RPM or 45 RPM (Fig. 7).
1
3
5. Start: Gently push the START button (Fig. 8a). The turntable
will start and the tone arm automatically will move to the
lead-in groove. When the record has finished playing, the
tone arm automatically will return to the tone arm rest and
the turntable will shut off.
6. Stop: To stop playing the record before it reaches the end,
press the STOP button (Fig. 8b). The tone arm will lift and
return to the tone arm rest, and the turntable will shut off.
7. Pause: To pause the record before it has completed playing,
press the tone arm Lift button (Fig. 8c). Press the Lift button
again to continue playing the record.
Release
P R B
(flashes
in Red and Blue)
Listening to Music
1. Once pairing has been performed, press and hold the wireless
function button for about 2 seconds to turn on the Bluetooth
function. Turn on the Bluetooth receiver device. Indicator will
turn blue when the signal is transmitted correctly.
2. Play and enjoy music according to the Automatic Operation
(See below) or Manual Operation (See Page 6) instructions.
3. Press and hold the wireless function button for 2 seconds to
cut the connection to the Bluetooth receiver device. Indicator
will turn off.
NOTE: When Bluetooth is connected, and you push the wireless
function button twice, Bluetooth is unconnected. When you
push it once again, Bluetooth is connected again. When pairing
is performed, and you cannot hear the sound from the Bluetooth
receiver device even if you play music, Bluetooth communication
may be cut. Push the wireless function button to connect
Bluetooth communication.
About Indicator Display
The wireless function button's Indicator LED displays the following
wireless operating status by flashing or turning on:
Operating status LED display patterns
Pairing Searching for device
Waiting to be
connected
Connect
Connecting
Connecting to Stereo System (Wired Connection)
1. Connect the output cable's mini-plug to the ANALOG OUT on
the rear panel.
2. Connect the output cable's red RCA-type pin-plug to the right
channel input and the white RCA-type pin-plug to the left
channel input of your stereo system (Fig. 3, page 4).
3. With the tone arm still fastened to the tone arm rest, slowly
turn the turntable platter clockwise ten times, to make certain
the automatic mechanism is fully cycled.
4. Remove the vinyl tie that holds the tone arm on its rest.
5. Connect the power cable plug to an AC outlet. Make sure the
AC outlet supplies the proper voltage for the AT-LP60-BT you
are using.
Caution: You cannot adjust the volume if there is no volume
adjustment on the connecting speaker, etc.
Figure 4
Stylus assembly
Stylus guard
Figure 5
Initial Setup (continued)
Red
Stylus ("Needle")
45 RPM adapter
English
Blue
Flashing
Lit
5