Battery Handling; Battery Status; Battery Charger; Transport And Storage - Husqvarna 136Li Manual De Instrucciones

Battery status

The display shows the battery capacity and if there are
any problems with the battery. The battery capacity is
displayed for 5 seconds after the machine is switched off
or the battery indicator button (1) is pressed. The warning
symbol on the battery is lit when an error has occurred
(2). See fault codes. (Figure 49)
LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit.
LED 1, LED 2 are lit.
LED 1 is lit.
LED 1 flashes.

Battery charger

WARNING! Risk of electric shock and
!
short circuiting. Use approved and intact
wall sockets. Make sure that the cable is
not damaged. Replace cable if it appears
to be damaged in any way.
Connect the battery charger
• Connect the battery charger to the voltage and
frequency specified on the rating plate. Put the
electric plug in a earthed socket-outlet. The LED on
the battery charger flashes green once. (Figure 50)
• The battery will not be charged if the battery
temperature is over 50 °C.
Connect the battery to the battery
charger
Regularly check that the battery charger and the battery
are intact. See also instructions under the Maintenance
heading.
The battery must be charged before using it the first time.
The battery is only 30% charged when delivered.
• Connect the charger to the battery. (Figure 50)
• The green LED on the charger is lit during charging.
(Figure 51)
• When all the LEDs are lit on the battery, it is fully
charged. (Figure 52)
• Disconnect the charger from the battery.
• Pull out the plug. Never jerk the power supply cable to
disconnect it from the wall socket.
1156931-38 Rev.2 2016-11-29

BATTERY HANDLING

Battery status
Fully charged (75-100%).
The battery is 50%-75%
charged.
The battery is 25%-50%
charged.
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
Charging status
Lithium-ion batteries can be charged at whatever
charging level. The charging process can be cancelled or
started whatever the battery's charge level is. (Figure 53)
LED display
LED 1 flashes.
LED 1 is lit, LED 2 flashes.
LED 1, LED 2 are lit, LED 3 flashes.
LED 1, LED 2, LED 3 are lit, LED 4
flashes.
LED 1, LED 2, LED 3, LED 4 are lit.

Transport and storage

• The contained lithium-ion-batteries are subject to the
Dangerous Goods Legislation requirements.
• For commercial transports e.g. by third parties,
forwarding agents, special requirement on packing
and labeling must be observed.
• For preparation of the item being shipped, consulting
an expert for hazardous material is required. Please
also observe possibly more detailed national
regulations.
• Tape or mask off open contacts and pack up the
batteriy in such a manner that it cannot move around
in the packing.
• Always remove the battery for storage or transport.
• Store the battery and the battery charger in a dry,
moisture-free and frost-free space.
• Do not store the battery in places where static
electricity can occur. Never store the battery in a metal
box.
• Store the battery and the battery charger where the
temperature is between 5 °C and 45 °C and never in
direct sunlight.
• Store the battery charger only in an enclosed and dry
space.
• Be sure to store the battery separate from the battery
charger. Store the equipment in a lockable area so
that it is out of reach of children and unauthorized
persons.
• Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
• The guide bar cover must always be fitted to the
cutting attachment when the machine is being
transported or in storage, in order to prevent accident
contact with the sharp chain. Even a non-moving
chain can cause serious cuts to yourself or persons
you bump into with an exposed chain.
• Secure the machine during transport.
Charging status
The battery is 0%-
25% charged.
The battery is 25%-
50% charged.
The battery is 50%-
75% charged.
Battery is 75%-
100% charged
When all the LEDs
are lit on the battery,
it is fully charged.
–
English 21