Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
In "
" mode:
store
-
the CTCSS tone or DCS code. The blinking stops.
In "
" mode:
store
-
the CTCSS tone or DCS code of the reception (RX).
- "TX" blinks in addition to the selected data.
- Rotate PUSH knob (6) to
set
desired CTCSS tone or DCS code of the transmis-
sion (TX).
- Press MEM-STORE key (5) for 2 seconds to store the CTCSS tone or DCS code
of the transmission (TX). The blinking stops.
- Long press MODE-CTCSS/DCS key (18) to
See tables on page 51.
19) VOX ~ VOX SET
VOX
(short press)
The VOX function allows transmitting by speaking into the original microphone
(or in the optional vox microphone) without pressing the PTT pedal (23). In
case of the use of an optional vox mike connected to the rear panel of the
radio - VOX MIC jack (E), the original microphone doesn't work.
Press the VOX key (19) in order to
on the LCD. A new pressure on the VOX key (19) switches the function off.
"VOX"disappears from the LCD.
VOX SET
(long press)
Press for 2 second the VOX-VOX SET key (19) in order to
function (if the VOX function is off, this will turn the function on and display
"VOX" on the LCD). "
" appears on the LCD.
Three features are possible: Sensitivity level, Anti-Vox level and Vox Delay
time.
Press s/t keys (10) in order to
select
feature.
Rotate PUSH (6) to
set
the feature.
store
Press MEM/STORE key (5) to
Once the adjustments are done, press the VOX-VOX SET key (19) in order
to
quit
the VOX SET function. If any adjustment have been done during 5
quit
seconds, the transceiver will
- Sensitivity "
": allows the adjustment of the microphone (original one
or optional vox) for an optimum transmission quality. Adjustable level from 1
(high sensibility) to 9 (low sensibility). Default: 5.
- Anti-Vox "
": allows disabling the transmission generated by the surround-
ing noise. The level is adjustable: 0 (OFF), from1 (high level) to 9 (low level).
Default: 9.
disable
CTCSS tone or DCS code.
activate
the VOX function. "VOX" is displayed
activate
the VOX SET
to the following feature. LCD shows the
skip
and
into the next feature.
the VOX SET function automatically.
- Delay Time "
": allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from 1 (short
time delay) to 9 (long time delay). Default:1.
20) SPLIT ~ SPLIT SET
SPLIT
(short press)
The SPLIT function allows to
transmit
Press SPLIT key (20) to
enable
seconds.
Press SPLIT key again to
disable
5 seconds.
Note: Channel, Band and Frequency are blinking if the SPLIT function is active.
SPLIT SET
(long press)
Long press SPLIT-SPLIT SET key (20) to set repeater's OFFSET and DIRECTION
Press s/t (10) to
alternate
the menu list.
Rotate PUSH (6) knob to
set
Press MEM/STORE key (5) for 2 seconds to
Press SPLIT key (20) or wait for 5 seconds to
- FREQUENCY OFFSET: frequency blinks on the LCD.
- DIRECTION: LCD shows "SPLiT"."
rent channel, "
" means negative offset set in current channel.
21) BAND ~ +10KHz
BAND
(short press)
Press BAND key (21) for
quick movement
~ F ~ 9 ~ H ~ I segments.
+10KHz
(long press)
Long press BAND-+10KHz key (21) to
"10K "
Long press BAND-+10KHz key (21) again to
disappears from the LCD.
22) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the set-
ting of the equipment into the dashboard easier.
See Cabling Diagram page 51.
10
receive
and
on separated frequencies.
repeater function, LCD shows "
repeater function, LCD shows "
between FREQUENCY OFFSET and DIRECTION in
desired feature.
store
and
skip
into next menu.
exit
SPLIT SET function.
" in LCD means positive offset set in cur-
skipping 200 kHz in A ~ B ~ C ~ D ~ E
enable
frequency +10KHZ. LCD shows
disable
frequency +10KHZ. "10K"
" for 5
" for
Publicidad
Tabla de contenido
