Publicidad
Cable Preparation
Remove the shield (as shown in the illustration) from the tip of the cable to which you are connecting the included Euroblock plug.
Supported wire gauge: 16 - 24 AWG
• Be sure to use a shielded cable.
• Do not solder the bare part of the core wire of the cable.
Entfernen Sie die Schirmung (siehe Abbildung) an der Spitze des Kabels, an das Sie den beiliegenden Euroblock-Stecker
anschließen möchten.
Unterstütze Aderstärken: 16~24 AWG
• Verwenden Sie ausschließlich geschirmtes Kabel.
• Verlöten Sie niemals den blanken Teil des Kabelkerns.
Enlevez la protection (comme indiqué dans l'illustration) du bout du câble auquel vous branchez la prise Euroblock incluse.
Type de câble accepté: 16~24 AWG
• Utilisez un câble blindé.
• Ne soudez pas la partie dénudée du fil central du câble.
Extraiga la protección (como se muestra en la ilustración) de la punta del cable al que está conectando el conector Euroblock incluido.
Tamaño permitido del cable: 16~24 AWG
• Asegúrese de usar un cable blindado.
• No suelde la parte pelada del núcleo del cable.
付属のユーロブロックプラグに取り付けるケーブルは、図のようにむき出しにしてください。
使用可能電線径 : 16 ∼ 24 AWG
ケーブルは、必ずシールド線を使用してください。
ケーブルのむき出し部分に半田めっきしないでください。
Specifications
1. ANALOG INPUT CHARACTERISTICS
Input Terminals
IN 1–8
*1. In these specifications, when dBu represents are specific voltage, 0 dBu is referenced to 0.775 Vrms.
*2. AD converters are 24 bit linear, 128times oversampling. (Fs=44.1 kHz, 48 kHz)/64times oversampling. (Fs=88.2 kHz, 96 kHz).
2. ANALOG OUTPUT CHARACTERISTICS
Output Terminals
OUT 1–8
*1. In these specifications, when dBu represents are specific voltage, 0 dBu is referenced to 0.775 Vrms.
*2. DA converters are 24 bit linear,128times oversampling. (Fs=44.1 kHz, 48 kHz)/64times oversampling. (Fs=88.2 kHz, 96 kHz).
3. Pin Assignment of Euroblock connectors
IN/OUT
12 11 10
+
–
G
CH8
4. Included Accessories
12-pin Euroblock plug x4
Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to
change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not
be the same in every locale, please check with your Yamaha dealer.
Shielded Cable
Actual Load Impedance
10k Ω
Actual Source Impedance
75 Ω
9
8
7
6
5
4
+
–
+
–
G
G
CH7
CH6
7mm
30mm
For Use With Nominal
600 Ω Lines
For Use With Nominal
10k Ω Lines
3
2
1
12 11 10
+
–
+
–
G
G
CH5
CH4
7
Input level
Max. before clip
+24 dBu (12.28 V)
Euroblock (balanced)
Output level
Max. before clip
+24 dBu (12.28 V)
Euroblock (balanced)
9
8
7
6
5
4
3
+
–
+
–
+
G
G
CH3
CH2
Connector
Connector
2
1
–
G
CH1
Publicidad
