Stopping The Saw; Incidents During Sawing; Adjustments: Straight Line Sawing; Maintenance - Husqvarna FS 3500 Manual Del Operador

7

STOPPING THE SAW

(See Fig. 1, 2 and 3)
For EMERGENCY STOP, press down the RED
PALM SWITCH (1T ) on the cowl. This will
stop the engine, disconnect power to all
e l e c t r i c a l i t e m s e x c e p t l i g h t s a n d t h e
park ing brake will engage. Reset the RED PALM
S W I TC H ( 1 T ) by t u r n i n g t h e re d b u t to n i n t h e
direction of the arrows (Clockwise) until it pops up. Then
restart engine.
DO NOT use the EMERGENCY STOP SWITCH (1T) for
normal, routine engine stopping.
•
Move The Control Lever (1S) to the Neutral (1V)
position.
•
Raise the Diamond Blade (2E) out of the cut by
pressing the Red Button (1R) on the Control Lever (1S)
upward until the Diamond Blade (2E) clears the surface.
•
Set the Engine Throttle (1P) to the IDLE position.
•
Turn off the Water Valve (3A).
•
STOP the engine by turning the Engine Start Switch (1I)
to the OFF position.
DO NOT turn Key Switch (1l) off while saw is mov-
ing.

8 INCIDENTS DURING SAWING

(See Fig. 1 and 2)
If ENGINE STOPS during sawing, check the following:
•
Engine out of fuel—Check Fuel Gauge (1G).
•
Lack of water signals the Water Safety Switch (1E) to stop
the engine. Press button (1E) to reset the switch, and then
restart the engine.
•
Excessively fast cutting speed will stall engine.
•
Red Palm Emergency Switch (1T) has been pressed
down. Reset by turning red button until it pops
upward.
If DIAMOND BLADE (2E) STOPS during sawing, check:
•
Drive belt tension is inadequate.
SAW LOWERS TOO FAST:
•
The lowering rate of the saw can be adjusted using the
Flow Control Valve at the rear or the saw. If the saw falls
too quickly, turn the knob on the Flow Control Valve
CLOCKWISE until an adequate lowering rate is set.
If the ENGINE or BLADE STALLS for any reason, raise the blade
completely from the cut, inspect the machine thoroughly
before restarting the engine. When lowering the blade into
a partial cut, align the blade exactly with the cut to prevent
damage to the blade.
26
Entrust all repairs to your authorized dealer only.
9

ADJUSTMENTS: STRAIGHT LINE SAWING

While cutting, the saw may steer to the right from the
required straight line marked on the cutting surface (if the
Diamond Blade (2E) is installed on the right hand side). If this
occurs, the Rear Axle of the saw can be pivoted to compensate
for this situation.
•
Loosen the three (3) 1/2"-13 UNC Bearing Mounting Bolts
on the Left End of the rear axle.
•
The axle is adjusted by turning the M12 Adjustment Bolt
located at the rear lower left of saw cowl.
•
If the saw steers to the RIGHT while sawing, Turn the Ad-
justment Bolt COUNTER-CLOCKWISE.
•
If the saw steers to the LEFT while sawing, Turn the
Adjustment Bolt CLOCKWISE.
•
Verify transmission belts and pulleys are in line.
•
Re -tighten the three (3) 1/2"-13 UNC Bearing
Mounting Bolts.
10

MAINTENANCE

B e f o r e p e r f o r m i n g a n y m a i n t e n a n c e ,
A LWAY S p a r k t h e m a c h i n e o n a l e v e l
surface with the Engine OFF and the Engine Start
Switch in the OFF position.
After each use: CLEAN the machine.
LUBRICATION:
ENGINE OIL: Check daily. Change Engine Oil and Oil Filter
after every 50 HOURS of operation. 10W30 is generally
recommended.
∗
Gas Models: 10W30 MS, SD, SE or better
Pro 35 III
Capacity: 4 Qt. - Gas
4.5 Qt - Dsl
S T A N D A R D B A L L
BEARINGS: Lubricate daily with a Premium Lithi-
um 12 based grease conforming to NLG1 GRADE #2
consistency. (Pro 65 Basic, Pro 40, Pro 35)
FRONT WHEEL BEARINGS: Lubricate daily.
Lubricate every 50 hours:
•
Rear Axle Bearings
Lubricate every 100 hours:
•
Front Axle Pivot Bearings
Pro 40 III Pro 65 III
5 Qt. 7 Qt.
B E A R I N G B L A D E S H A F T