Loading / Unloading The Tool - Campbell Hausfeld SB51400 Manual De Instrucciones De Operación

Operating the Tool
(Continued)
2. Turn the tool so the
air inlet is facing up.
Place 4-5 drops of 30
W non-detergent oil
into air inlet. Do not
use detergent oils, oil additives, or
air tool oils. Air tool oils contain
solvents which will damage the
tool's internal components.
3. After adding oil, run
tool briefly. Wipe off
any excess oil from the
cap exhaust.
RECOMMENDED HOOKUP
The illustration shows the
recommended hookup for the tool.
1. The air
compressor
must be able
to maintain a
minimum of
60 psi when the tool is being used.
An inadequate air supply can cause
a loss of power and inconsistent
driving.
2. An oiler can be used to
provide oil circulation
through the tool. A
filter can be used to
remove liquid and solid
impurities which can rust or "gum
up" internal parts of the tool.
3. Use 3/8 inch air hoses
with a minimum
working pressure of
150 psi. Use 1/2 inch
air hoses for 50' run
or longer. For better performance,
install a 3/8 inch quick plug (1/4 inch
NPT threads) with an inside diameter
of .315 inch (8mm) on the tool and
a 3/8 inch quick coupler on the air
hose.
4. Use a pressure regulator on the
compressor, with an operating
pressure of 0 -125 psi. A pressure
regulator is required to control
the operating pressure of the tool
between 60 and 100 psi.
SINGLE SEQUENTIAL MODE
This mode
requires the
trigger to
be pulled
each time
a fastener is driven. The tool can be
actuated by depressing the WCE against
the work surface followed by pulling
the trigger.
The trigger must be released to reset
the tool before another fastener can be
driven.
CHECKING THE WORK CONTACT
ELEMENT (WCE)
the Work Contact Element (WCE)
trip mechanism before each
use. The WCE must move freely
without binding through its entire
60 psi
travel distance. The WCE spring
Min.
must return the WCE to its fully
extended position after being
120 psi
depressed. Do not operate the tool
Max.
if the WCE trip mechanism is not
operating properly. Personal injury
may occur.
1. Disconnect the air
supply from the tool.
2. Remove all
fasteners
from the
magazine
(see
Loading / Unloading).
150 psi WP
3. Make sure the trigger
3/8 inch
and work contact
I.D.
element (WCE) move
freely up and down
without sticking or
binding.
4. Reconnect
air supply
to the
tool.
5. Depress the Work
Contact Element
(WCE) against the
work surface without
pulling the trigger. The
tool MUST NOT OPERATE. Do not
use the tool if it operates without
6. Remove the tool from
7. Pull the
Check the
operation of
8. Depress
must not be used. Do not actuate
the tool unless the tool is placed
fi rmly against the work piece.

LOADING / UNLOADING THE TOOL

1. Always disconnect the tool from
2. Push
3a. For nails,
5
SB514000
pulling the trigger. Personal injury
may result.
the work surface. The
Work Contact Element
(WCE) must return to
its original down
position. The tool MUST NOT
OPERATE. Do not use the tool if it
operates while lifted from the work
surface. Personal injury may result.
trigger
and
depress
the work
contact element (WCE) against the
work surface. The tool MUST NOT
OPERATE.
the Work
Contact
Element
(WCE)
against the work surface. Pull the
trigger. The tool MUST OPERATE.
An improperly
functioning tool
the air supply before loading
fasteners.
down on
the latch
button.
Pull back
on the magazine cover.
insert a
stick of
Campbell
Hausfeld
nails or equivalent (see "Fasteners"
section) into the magazine. Make
sure the pointed ends of the
fasteners are resting on the bottom
ledge of the magazine when
loading. Make sure the nails are not
dirty or damaged.
www.chpower.com
Latch
button