During Use; After Use - MaxPro PROFESSIONAL MPAG2600/230L Manual De Uso

penetra water pipe will cause property damage or an electrical shock)
• Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful
(contact with or inhala of the dust may cause allergic rea
operator or bystanders); wear a dust mask and work with a dust extr
• Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in c
with ves for wood c wear a dust mask and work with a dust extr
connectable
• Follow the dust-related na requirements for the materials you want to work with
• Be careful when cu g grooves, especially in suppor
country-specific regula regula
• Clamp the work piece in case it does not remain sta
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with a capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• Inrush currents cause short voltage drops; under unfavourable power supply c
equipment may be affected (if the system impedance of the power supply is lower than 0,104 + j0, 065
Ohm, disturbances are unlikely to occur); if you need further clarifica
supply authority
• If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect
the plug;
• Never use the tool with a damaged cord
• In case of electrical or mechanic
• In case of current interrup or when the plug is accidentally pulled out, unlock the on/off switch
immediately in order to prevent uncontrolled rest

AFTER USE

• A er switching off the tool, never stop the rota
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not le
una ended
SYMBOLS
Read the manual
Warning
Double isula
Wear eye prot
OPERATING INSTRUCTION
Moun
Never insert the mains plug in a socket when you are moun
The handle (1) can be mounted on the angle grinder in three differen
the right.
ANTI-VIBRATION AUXILIARY HANDLE
6
s and/or respiratory diseases to the
evice when connectable
g walls (slots in suppor g walls are subject to
re to be observed under all circumstances)
ry from its own weight
you may contact your local power
ately switch off the tool and disconnect the plug
of the accessory by a lateral force applied against it
Wear ear prot
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
/or removing the handle.
e
GB
This front handle incorporates a flexible vibra
reduce vibra
Moun
1. Carefully fit the clamp of the guard on the spindle sha
2.Turn the guard so that the exposed part of the disc is located as far as possible from your hand on the
handle
device when
Moun
1. Pull the mains plug.
2. Press and hold down the spindle locking mechanism.
3. Unscrew the flange nut with the hook wrench.
Moun
These discs are not included in the product contents. The diameter of the discs used may not exceed
180mm/230mm. The permissible speed specified on the discs must be greater than the max, speed of your
s, other
angle grinder (see Technical data).
1. Mount the flange C on the spindle sha
is securely seated on the spindle.
2. Place the disc on the flange C with the swell forward.
3. Depending on the disc type, screw the flange nut B onto the spindle as shown in the following figures:
- Grinding disc
For thick grinding discs, the protruding ring E of the flange nut B must extend into the disc hole.
-Cut-off disc
For thin cut-off discs, the protruding E of the flange nut B must be poin
4.Press and hold down the spindle locking mechanism on the upper side of the device. Tighten the flange
nut with the hook wrench. Then release the spindle locking mechanism.
5.Check whether the mounted disc is able to freely rotate under the guard.
6.Keep the device away from your body. Insert the plug in a socket, turn on the device and let it run for
approximately 30 seconds without applying a load. Pull the plug and check whether the disc is firmly
seated.
va g
Before you start working with the two-handed angle grinder, check whether the voltage stated on the
specifica
va
1. Insert the mains plug in a properly installed socket.
2. Press the safety bu on (3) and then the On/Off switch (4).
3.Push forward switch knob (3) and press down switch (4) to start the angel grinder, release switch (4) to
stop the grinder, for a con
the switch; press down switch (4) to unlock the switch.
Adjus
1.Turn the guard so that the exposed part of the disc is located as far as possible from your hand on the
handle.
2. Secure the guard with a clamp that is held in place with a screw.
Note:
If applicable, you must stop working in order to adjus
Grinding and fine grinding
ht and on
"Grinding" refers to working on a surface with a very coarse tool (e. g. a file or sandpaper). When grinding,
a large amount of material is removed, this is therefore always the first work step. A erwards, the surface
bsorbing moun
rease comfort.
rd (Fig.7)(Fig.8)
ry!
ay be very hot!
t-off, grinding and buffing discs (Fig.9)(Fig.10)
roove forward and turn it un
va
ate of the angle grinder corresponds to the available grid voltage.
g, push forward switch knob (3) again and release switch (4) to lock
(only for the model: MPAG2600/230L)
rd (Fig.5)
GB
etween the bolt and handle grip to
ks into place and
to the outside.
rd.
7