Bluetooth ® Pairing - Hama CONES Instrucciones De Uso

Note – Charging / Battery level
• It takes approx. 5-6 hours to completely charge the product.
• The speaker's battery can be charged whether the speaker is
on or off.
• If the battery level is less than 10%, an announcement will play.
You will only receive this information if the speaker is on.
• Depending on the terminal device connected ( Bluetooth
speakers' battery level will appear on the device.
• The actual battery life varies depending on use of the device, the
settings and the ambient conditions (rechargeable batteries have a
limited service life).
4.4 Audio playback via the included audio cable
(3.5 mm jack)
• Ensure that the speakers are switched off.
• Connect the 3.5 mm Y-audio cable to your terminal device (MP3
player, smartphone, computer, etc.) using the main connector
(somewhat thicker).
• Plug the two other connectors into the AUX-IN inputs (3) on the
speakers.
• Set the volume on your terminal device to a low level.
• Switch on the speakers as described in 4.1 Switching on/off the
product . The status LEDs (2) will flash steadily in blue.
• Start and control audio playback on the connected terminal device
accordingly.
Note
Please note that you cannot establish the Bluetooth
described under 4.5 and 4.6 if an audio cable is connected.
4.5 Bluetooth pairing
®
Note
• Check whether your mobile device (MP3 player, mobile phone,
etc.) is Bluetooth
capable.
®
• If not, you can only use the speakers for playback using the
included audio cable.
• Note that the maximum range for Bluetooth
obstacles such as walls, people, etc.
• Make sure that your Bluetooth
Bluetooth
is activated.
®
• Make sure that the speakers are located within the Bluetooth
of max. 10 metres.
• Switch on the speakers as described in 4.1. Switching on the product .
C
The speakers will search for a connection.
C
Alternatively you can press and hold the function buttons (5) on both
speakers at the same time until the status LEDs (1) alternate red and
blue flashes.
• Press and hold the function button (5) on the individual speaker until
the status LED (1) alternates red and blue flashes.
• Open the Bluetooth
settings on your terminal device and wait until
®
Cones appears in the list of Bluetooth
• Select Cones and wait until the speakers are listed as connected in
the Bluetooth settings on your terminal device. An announcement
®
confirms that connection was successful.
), the
®
connection
®
is 10 metres without
®
-capable terminal device is on and
®
®
devices found.
®
C
The status LEDs (1) on both speakers will flash once in blue at regular
intervals.
• The status LED (1) on the individual speaker flashes once at regular
intervals.
Note – No connection possible
• If the speakers do not appear in the list of available devices,
quickly press the function button (5) twice in succession.
• A voice announcement plays and the speakers will search for a
connection to the terminal device.
Note – Bluetooth
Some terminal devices require a password in order to connect to
another Bluetooth
• If your terminal device requests a password for connection to the
speakers, enter 0000.
Note
• The speakers always store the last eight terminal devices paired.
• The speakers will automatically connect to the last terminal device
paired when it is switched on the next time.
• The speakers will exit pairing mode if no Bluetooth
is established within two minutes. To activate pairing mode again,
see the section Note – No connection possible.
4.6 Automatic Bluetooth
pairing)
• Make sure that your Bluetooth
Bluetooth
is activated.
®
• Make sure that the speakers are located within the Bluetooth
of max. 10 metres.
• Switch on the speakers as described in section 4.5 Bluetooth
• An announcement confirms that connection was successful.
C
The status LEDs (1) on both speakers flash once in blue at regular
intervals.
• The status LED (1) on the individual speaker flashes once at regular
intervals.
Note – Connection impaired
• After the speaker and terminal device have been paired, a
range
connection is established automatically. If the Bluetooth
connection is not established automatically, check the following:
• Check the Bluetooth
whether Cones is connected. If not, repeat the steps listed under
Bluetooth
®
• Check whether your terminal device and the speaker are less than
10 metres apart. If not, move them closer together.
• Check whether obstacles are impairing the range. If so, move the
devices closer together.
• Check whether the audio cable is connected to the speaker. If
so, disconnect it.
password
®
device.
®
connection (after successful
®
-capable terminal device is on and
®
settings of your terminal device to see
®
pairing.
connection
®
range
®
pairing.
®
®
3