Shop-Vac SS11 Serie Manual Del Usuario página 4

TOOL HOLDER
(Not standard with all models)
1. With rear of unit facing you, take tool holder and position it with tabs facing rear of unit
(Figure 20).
2. Place "J" shaped tabs into the slots on cord wraps (Figure 21).
3. Press down until tabs snap into place.
4. Press down on center of tool holder until tab latches on bottom of lid (Figure 22).
21
20
INSTALLING THE CARRIAGE HANDLE
(Not standard with all models)
Follow the instructions for the carriage handle that came with your vacuum.
If your side tank handles look like the ones pictured to the right,
follow these instructions (Figure 23).
You will find one carriage handle and a handle pack containing two side tank handles, four
handle supports and eight screws. Assemble as follows:
1. Take two handle supports and two 1" screws. Place screws
through the hole provided in center of each support
(Figure 24).
2. Position the tank, in the upright position, with the inlet facing
you. Put the support assemblies inside the tank, then place
the screws through the holes provided on left side of the tank.
Make sure the plastic portion is located inside the tank. Turn
the supports until the back of the supports fit flush against the
inside curve of the tank (Figure 25).
3. Remove any webbing that attaches the tank handles to each
other. Take the side tank handle with the letter L and position
it on the outside of the tank where the support assemblies
are installed. The U-shaped cutout on the bottom end of the
handle must face the rear of the tank. Secure the side tank
handle to the tank with the screws in the support assemblies
(Figure 26).
4. Repeat steps 1 to 3 using right side of tank and the remaining side tank handle marked with
the letter R.
5. Position metal carriage handle outside of tank and under
the tank handles. Be sure to spread ends of carriage handle
when assembling to prevent damage to tank. Line up holes in
ends of carriage handle with holes in bottom of tank handles.
Make sure carriage handle is in the U-shaped cut on the tank
handles (located towards rear of unit). Secure with 1½" screws
provided (Figure 27).
If your side tank handles look like the ones pictured to the right,
follow these instructions (Figure 28).
6. Attach carriage handle to tank by inserting bolt through the center hole of handle and tank,
22
(Not standard with all models)
Attach side handles to tank with screws provided (Figure 30).
23
(Not standard with all models)
24
WALL OUTLET BEFORE REMOVING THE TANK COVER.
When using the reusable dry filter
to pick up dust and dry material,
you must install foam sleeve
and reusable dry filter to ensure
proper filtration. If the vacuum
has been used to pick up liquids,
the foam sleeve must be cleaned
and dried before installing for dry
25
pick up. With tank cover in an
upside down position, slide foam
sleeve down over lid cage pulling
until foam sleeve completely
covers lid cage (Figures 31, 32).
Center the reusable dry filter on lid
cage (Figure 33), slide mounting
ring down over filter until ring is
positioned against the ribs of the lid
26
cage (Figure 34). The reusable dry
filter should always be in position over the foam sleeve for dry pick
up. To remove the filter for cleaning, remove mounting ring and filter
from lid cage (Figure 35). To clean the reusable dry filter, shake
off excess dirt and dust or (depending on the condition of the filter)
rinse with water. Allow the filter to dry completely and reinstall.
DO NOT MACHINE WASH OR DRY.
(Not standard with all models)
27
NOTE: If foam sleeve is in postion over lid cage, it must be removed before installing cartridge
filter.
The cartridge filter can be used for wet or dry pick up; installation is the same for both. When
picking up large quantities of liquid please refer to the Wet Pick Up Operation section in this
manual. Use the cartridge filter in position over the lid cage for most general dry material pick
up. With the tank cover in an upside down position, slide the cartridge filter down over the
lid cage, pushing until the filter seals against the cover (Figure 36). Place filter retainer into
the top of the cartridge filter, hold the tank cover with one hand, turn the handle on the filter
28
retainer clockwise to tighten, locking the filter into place (Figures 37 & 38). To remove the
filter for cleaning, again hold the tank cover and turn the filter retainer counter-clockwise to
loosen and remove, slide the cartridge filter off the lid cage (Figures 39 & 40). To clean the
cartridge filter shake or brush off excess dirt or rinse (from the inside of the filter) with water,
dry completely (approximately 24 hours) and reinstall (Figures 41 & 42). NOTE: If the filter
has been used for wet pick up, it must be cleaned and dried before using for dry pick up.
secure with nut provided. Attach side handles with screws provided. Be sure to spread ends
of carriage handle when assembling to prevent damage to tank (Figure 29).
29
Item
3
5
1
1
2
2
3
4
4
5
SIDE TANK HANDLE ASSEMBLY
DRY PICK UP
INSTALLING FOAM SLEEVE AND
REUSABLE DRY FILTER
WARNING
– ALWAYS DISCONNECT THE PLUG FROM THE
31
33
INSTALLING THE CARTRIDGE FILTER
36
37
Description
Metal tank handle
Side tank handle
#10 x 3/4" Screw hex head
Bolt 1/4 - 20 x 1/2"
1/4 - 20 Hex nut
30
32
34
35
38