Miele UO 8250 Instrucciones De Montaje página 7

Produktgruppen 522, 592
7 von 30
Danger!
Risk of injury during fitting.
Risk of electric shock. Before any service work is commenced, the machine must be disconnected from the mains.
Fitting can only be carried out with the washing machine or tumble dryer not installed. For deinstallation, see the appropriate
operating instructions.
Risk of crushing. Wear slip-proof working gloves and safety shoes.
Risk of crushing. When carrying out work, ensure that parts of the body, especially the hands and feet are not positioned under or
between machines.
Risk of accident. Ensure that children or pets cannot access the work area while fitting work is being carried out.
Risk of injury, particularly to the back. The relation of the weight of the machine to the physical strength of the technician must be
taken into account. For machine weight details, see the appropriate operating instructions.
Risk of toppling over. Risk of injury due to incorrect fitting.
Always bolt the machine to the plinth.
With a single machine installation, secure the plinth to the floor with the fastening accessory, Mat. no. 01497252, supplied with the
kit. This is supplied with the kit.
With floor fastening, secure all four plinth feet.
Note
The plinth may only be used with the following Miele models:
UO 8250 / UG 8250 = PT 8251, PT 8251 COP, PT 8253, PT 8255, PT 8257
UO 8330 / UG 8330 = PT 8331, PT 8331 COP, PT 8333, PT 8335, PT 8337
Note
Tools required:
Spirit level for plinth levelling
1 x Drill
1 x Drill bit Ø 12 mm
1 x Open spanner 13 mm for M8 nut
2 x Open spanner 10 mm for M6 nut
1 x Torx 20 screwdriver
Note
The fitting kit - Plinth UO 8250 Mat. no. 07761970, or fitting kit - Plinth UG 8330, Mat. no. 07762000, contains the following:
1 x Plinth UO 8250 or UO 8330
1 x Floor fastening accessory pack containing the following: 4 x Clamp, 8 x Galvanised washer B6.4, 4 x Bolt M6 x 20, 4 x Nut M6,
4 x Rawl plug S12, 4 x Washer 8.4, 4 x Hexagon head wood screw 8 x 65, 20 x Spacer plate, 8 x Washer 38 mm Ø
1 x Information sheet with these instructions and commissioning card. These fitting instructions are called Fitting instructions -
Plinth UO 8250 / UO 8330, UG 8250 / UG 8330 .
Note
The fitting kit - Plinth UO 8250 Mat. no. 07761950, or fitting kit - Plinth UG 8330, Mat. no. 07761990, contains the following:
1 x Plinth UO 8250 or UO 8330, 1 x Front panel, 2 x Side panel, 8 x Raised-head screw 4.8 x 9.5 and 4 x Rubber bumpers with
fitting kit - Plinth UG 8250, Mat. no. 07761950.
1 x Floor fastening accessory pack containing the following: 4 x Clamp, 8 x Galvanised washer B6.4, 4 x Bolt M6 x 20, 4 x Nut M6,
4 x Rawl plug S12, 4 x Washer 8.4, 4 x Hexagon head wood screw 8 x 65, 20 x Spacer plate, 8 x Washer 38 mm Ø
1 x Information sheet with these instructions and commissioning card. These fitting instructions are called Fitting instructions -
Plinth UO 8250 / UO 8330, UG 8250 / UG 8330 .
List of illustrations:
Fig. 1: Plinth height
Fig. 2: Floor fastening holes
Fig. 3: Floor fastening hole dimensions
Fig. 4: Floor fastening
Fig. 5: Clamp fitting
Fig. 6: Plinth UG 8250 / UG 8330
28.09.2010 Diese Unterlagen dürfen ohne unsere Genehmigung weder vervielfältigt noch Dritten zugänglich gemacht werden. Eigentumsrechte vorbehalten.
Umbau- und Montageanweisung
M.-Nr. 07946040