Reversing The Door Swing Of Your Appliance - NODOR Vinoteca V24B Manual De Instrucciones

Ocultar thumbs Ver también para Vinoteca V24B:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

that have become frayed or otherwise damaged. Do not use a
cord that shows cracks or abrasion damage along its length or
at either end.
When moving the appliance, be careful not to damage the
power cord. Electrical fuse protection of at least 10 amperes
must be provided. If the socket is no longer accessible once the
appliance has been built -in, suitable measures must be taken
during electrical installation to ensure that the appliance can be
disconnected from the mains.
Do not use your appliance with an extension cord unless this
cord has been checked and tested by a qualified technician or
service person. The extension cord must be a VED-Listed, 3-wire
grounding extension cord that has a grounding plug and outlet
and that the electrical rating of the cord is 220-240 volts and at
least 10 amperes.

Reversing the Door Swing of Your Appliance

Should you desire to reverse the opening direction, please follow
the instructions below.
1. Close the glass door, and remove the decoration plug 2.
Unscrew the top hinge pin 3 and lower hinge pin 8. Be careful to
support the glass door with hands to prevent it dropping after
removing the pins. (Figure 1&2)
2. Pull down to remove the glass door and place it on a padded
surface to prevent scratching it.
3. Remove the right top hinge plate 4 by unscrewing the four
screws 1 and get the left top hinge plate 6 from the plastic
bag that includes the instruction manual then install it at the
designated position on the opposite side.(Figure 1)
4. Remove the lower hinge plate 7 by unscrewing the four screws
9. Then turn it around and refit it on the opposite side.(Figure 2)
5. Turn around the glass door 180° and refit the hinge pin 3&8
through the top hinge plate 6 and lower hinge plate 7 into the
door. Make sure that the spacers which the hinge pins sit on are
correctly positioned.
6. Leveling the door by adjusting the screws that are used to fix
the top hinge plate and lower hinge plate.
1.
Screw
2.
Decoration Plug
3.
Top Hinge Pin
4.
Right Top Hinge Plate
5.
Glass Door
6.
Left Top Hinge Plate
Note
: All parts removed must be
saved to do the reinstallation of door.
7.
Lower Hinge Plate
8.
Lower Hinge Pin
9.
Screws
10. Cabinet
1
2
3
OPERATING YOUR WINE COOLER
The Wine Cooler should be placed in a position where the
ambient temperature is between 16-35°C/60~95ºF. If the ambient
temperature is above or below this range, the performance
of the unit may be affected. For example, placing your unit in
extreme cold or hot conditions may cause interior temperatures
to fluctuate. The range of 5-22°C/40~72ºF may not be reached.
(In-Column)The range of 5-18°C may not be reached. (Built-in)
Note
:
When you use the Wine Cooler for the first time or
restart the Wine Cooler after having been shut off for a
long time, there could be a few degrees variance between
the temperature you select and the one indicated on the
LED readout.
This is normal and it is due to the length of the activation
time. Once the Wine Cooler is running for a few hours
everything will be back to normal.
If the unit is unplugged, power lost, or turned off, you
must wait 3 to 5 minutes before restarting the unit. If you
attempt to restart before this time delay, the Wine Cooler
will not start.

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Vinoteca v41bVinoteca v61b

Tabla de contenido