Hdmi In 1-6 Video Inputs; Composite In 1-2 Video Inputs; Composite Video Output; Component Video - Rotel RSP-1572 Manual De Instrucciones

18
Note: For proper operation, all HDMI components and TVs connected
to the unit should be compatible with the HDMI Version 1.1 standard
or higher. The HDMI digital connections are usually compatible with
DVI components with an appropriate DVI-D cable adapter. For more
information, see the section HDMI:Frequently Asked Questions, in this
manual.
This Rotel processor provides upscaling and downscaling for the various
analog video formats. Composite Video or Component Video signals can
be scaled to 480p/576p, 720p, 1080i and 1080p by choosing the
appropriate output setting in the VIDEO/HDMI menu.
Note: The HDTV Component Video output is subject to HDCP copy
protection. It may not display 720p or 1080i resolution when the source
signal incorporates copy protection.
HDMI IN 1–6 Video Inputs
i
HDMI inputs provide various digital video connections for use with
components that have either HDMI outputs or DVI-D outputs (with an
appropriate DVI-HDMI adapter). HDMI connections carry video signals in
all formats including 3D signals up to 1080p/24Hz. The implementation
of HDMI supports audio signals, or a separate audio connection from
an HDMI component.
Six inputs, labeled HDMI VIDEO IN 1–6, accept signals from source
components.
COMPOSITE IN 1–2 Video Inputs
Two inputs accept standard composite video signals from source components
using standard 75 ohm RCA video cables.

COMPOSITE Video Output

e
The RCA jack, labeled COMPOSITE OUT, provide connections for
sending composite video signals for recording on a VCR or other
recording device.
Note: The unit cannot convert Component Video or HDMI signals to
composite video signals at the record output. Therefore, only signals
received at the composite video inputs are available at this output.
COMPONENT VIDEO 1–2

Video Inputs

r
Component Video connections split the video into three signals – luminance
(Y) and separate chrominance (PB and PR) signals, allowing delivery of a
reference-quality picture with high definition signals. Component Video
connections should be used for progressive scan DVD players and high-
definition digital television receivers. Each of these signals is carried by
a separate 75 ohm video cable with RCA connectors.
Two sets of inputs, labeled COMPONENT VIDEO IN 1–2, accept
Component video signals from source components.

COMPONENT Video output

w
The RCA jacks, labeled COMPONENT OUT, provide connections
for sending analog video signals for recording on a VCR or other
recording device.

High Definition TV Monitor Outputs

Two HDMI outputs of the unit send the High Definition video signals
to your TV monitor. The HDMI outputs can send all enhanced or high
e
]
RSP-1572 SURROUND SOUND PROCESSOR
definition video signals to a high-definition TV 2D (480p/576p, 720p,
1080i, or 1080p) and 3D (up to 1080p/24Hz).
The output resolution is specified in the VIDEO/HDMI setup menu. Analog
video signals (Composite and Component) in any resolution can be
converted to the desired resolution, except 3D and 1080p 24Hz signals
at the HDMI outputs.
Note: HDMI Video signals are passed through without scaling.
Note: If TV can not show the currently set HDMI resolution, press
"2CH" and "MUTE" keys together to on the front panel to change the
resolution to 480p/576p.

HDMI Monitor Outputs

]
There are two HDMI Outputs which send out HDMI signals in parallel.
The same signal is sent to both outputs at the same time. Only HDMI
output 1 is ARC enabled. Connect your ARC enabled TV's HDMI input
to this output.
Note: Your TV will most likely have more than one HDMI inputs. Not
all of them will be ARC enabled. Please use the ARC enabled HDMI
input of your TV. It should be labeled ARC next to the input.
Additional information for high definition outputs:
• Typically, choose the HDMI outputs with digital high-definition TVs
such as LCD, plasma, or DLP monitors. Use the Component Video
connections with analog high definition TVs such as CRT-based
direct view or projection monitors.
• HDTV Component Video output is subject to HDCP copy protection.
It may not display 720p,1080i or 1080p resolution when the
source signal incorporates copy protection. However, when Video
Out is set to 480p/576p in the VIDEO/HDMI menu, all sources
will be available.
• The video signal sent to the TV through the HDMI connection will
not be displayed properly unless all HDMI components in the
system, including the TV monitor, are compatible with the HDCP
copy protection standard.
• Only audio signals passed-through directly from the source component
are sent to the TV set through the HDMI connection. To send decoded
audio from the RSP-1572 to the TV, you must select 'TV mode' in
the VIDEO/HDMI menu.
• TV monitors with DVI-D connections can usually be connected to
the HDMI output of the processor with the use of an appropriate
24-pin DVI-HDMI adaptor. However, there are occasionally some
incompatibilities with older DVI-D equipped monitors.
• Use the scaler setting of the RSP-1572' s 'Analog Video Output to
match the resolution of your TV.
• 3D Video is only available through the HDMI outputs.