Initial Operation; Attaching The Auxiliary Handle; Dust Extraction - Metabo RS 14-125 Instrucciones De Manejo

Ocultar thumbs Ver también para RS 14-125:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Connect a FI circuit-breaker with max.
release current (30 mA) upstream when using the
machine outdoors.
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked auxiliary handle must be
replaced. Never operate a machine with a defective
auxiliary handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
Only use accessories that are surmounted by
brushes of the safety guard.
SYMBOLS ON THE TOOL:
........... Class II Construction
V............... volts
A .............. amperes
Hz ............ hertz
W ............. watts
~
.............. alternating current
rpm ......... revolutions per minute
.../min...... revolutions per minute
n.............. rated speed
4. Overview
See page 2.
1 Extractor connection piece
2 Threaded holes on gear housing (both sides)
3 Thumb screws
4 Auxiliary handle
5 Locking discs
6 2-hole spanner
7 Adjusting nut
8 Diamond cup wheel*
9 Support flange
10 Spindle
11 Spring-mounted ring brush
12 Spindle locking button
13 Opening segment (for working close to walls)
14 Safety guard
15 Handle
16 Lock (to prevent the machine from being
switched on unintentionally, or for continuous
operation)*
17 Trigger (for switching on and off)
18 Slide switch (for switching on/off) *
19 Electronic signal indicator
20 Speed adjustment wheel
* depending on equipment/not in scope of delivery

5. Initial Operation

Before plugging in the machine, check that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
5.1

Attaching the auxiliary handle

Always work with the auxiliary handle attached
(4)! Attach the auxiliary handle as shown.
See illustration A on page 2.
- Fit locking discs (5) to the left and right of the gear
housing.
- Fit the auxiliary handle (4) on the gear housing.
- Insert the thumb screws (3) to the left and right of
the auxiliary handle (4) and turn gently.
- Adjust the auxiliary handle to the required angle
(4).
- Manually tighten the thumb screws (3) to the left
and right.
5.2

Dust extraction

Always use a suitable dust extraction system:
Connect a vacuum cleaner to the extractor
connection piece (1).
For optimal dust extraction, use the connecting
sleeve 6.30796.
We recommend using an antistatic suction hose
with diameter 35 mm.
6. Attaching the accessory
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle must be at a standstill.
6.1
Locking the spindle
Press in the spindle locking knob (12) only
when the spindle is stationary!
- Press in the spindle locking button (12) and turn
the
spindle (10) by hand until you feel the spindle
locking button engage.
6.2
Fitting/removing the diamond cup wheel
See illustration B on page 2.
To fit:
- Fit the support flange (9) on the spindle. (10) The
flange should not turn on the spindle when prop-
erly attached.
- Lay the diamond cup wheel (8) on the support
flange (9) so that it lies flat along the support
flange.
- The two sides of the clamping nut (7) are different.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (7) is facing upward.
- Lock the spindle (see chapter 6.1). Turn the
clamping nut (7) clockwise using the 2-hole
spanner (6) to secure.
To remove:
- Lock the spindle (see chapter 6.1). Turn the
clamping nut (7) anticlockwise using the 2-hole
spanner (6) to unscrew.
en
E N G L IS H
7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Rs 17-125

Tabla de contenido