English; Technical Data; Ec Declaration Of Conformity; Safety Instructions - DeWalt DW710 Manual De Instrucciones

E N G L I S H

Technical data

Voltage
Power input
Power output
Max. blade speed
Blade diameter
Blade bore
Blade body thickness
Riving knife thickness
Riving knife hardness
Weight
Cutting capacities
Mitre saw mode
Mitre (max. positions)
Bevel (max. positions)
At 90°, at max. height 45 mm, max. width of cut
At 45° mitre, at max. height 45 mm, max. width of cut
At 45° bevel, at max. height 35 mm, max. width of cut
At 90°, max depth of cut mm 91, max width 20mm, max. cut off 15 mm
Saw bench mode
Max. depth of cut
EC-Declaration of conformity
DW710
D WALT declares that these Power Tools have been designed in
E
compliance with: 98/37/EEC, 89/336/EEC, 73/23/EEC, EN 61029-1,
EN 61029-2-11, EN 55014, EN 55014-2, EN 61000-3-2 & EN 61000-3-3.
For more information, please contact D
refer to the back of the manual.
Level of sound pressure according to 86/188/EEC & 98/37/EEC,
measured according to EN 61029-2-11:
L (sound pressure)
pA
L (acoustic power)
WA
* at the operator's ear
Take appropriate measures for the protection of hearing.
Weighted root mean square acceleration value according to EN 61029-2-11:
Director Engineering and Product Development
Horst Großmann
D WALT, Richard-Klinger-Straße 11
E
D-65510, Idstein, Germany
8
W 1,000
W 750
min
mm 247 - 250
mm 30
mm 1.8
mm 2.3
kg 24
left 48°
right 48°
left 45°
right 0°
mm 124
mm 84
mm 124
mm 0-45
WALT at the address below or
E
DW710
dB(A)* 90
dB(A) 103
DW710
< 2.5 m/s 2

Safety instructions

DW710 • Ensure the machine is fixed to a workbench in a stable position.
V 230 • This machine is of class I contruction; therefore earthed (grounded)
connection is required.
• Do not allow untrained people to operate this machine.
-1 2,950 • Do not force the tool. The tool will do the job better and safer at the
rate for which it was intended.
• Use the appropriate tool. The intended use is described in this
instruction manual. Do not force small tools or attachments to do the
job of a heavy-duty tool. Do not use the tool for purposes not intended;
43 ± 5 for example: do not use the tool to cut trees or logs.
• Keep the blade sharp.
• The max. allowable speed of the saw blade must always be equal to or
greater than the no-load speed of the tool specified on the nameplate.
• Do not use any spacers to make a blade fit onto the spindle.
• Do not use the saw for cutting any material other than wood and
plastics.
• Connect the machine to a dust collection device when sawing wood.
• Whenever you use the machine, report any faults in the machine as
soon as they are discovered.
• Select the correct blade for the material to be cut.
• Use only the blades specified in this manual, complying with EN 847-1.
• Do not use HSS blades.
• Do not use damaged or deformed saw blades.
• Always support long pieces.
• Take care that the selection of the saw blade accounts for the material
to be cut.
Sawing in mitre saw mode
• When performing vertical straight cross-cuts, adjust the sliding fence
correctly to ensure a clearance of max. 5 mm between the saw blade
and the fence (fig. T1).
• When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance for the application (fig. T2).
• Ensure that the upper portion of the saw blade is completely enclosed
in the mitre sawing mode.
• Refrain from removing any cut-offs or other parts of the workpiece from
the cutting area while the saw is running and the saw head is not in the
rest position.
Sawing in the bench mode
• Always adjust the sliding fence correctly to avoid contact with the lower
guard.
• Do not use saw blades with a body thickness greater or a width of
tooth smaller than the thickness of the riving knife.
• Ensure that the table is securely fixed.
• Always keep the push stick (44) in its place when not in use (fig. A2).
• Replace the table insert when worn.
• Slotting, rebating or grooving is not allowed.
• During transportation make sure that the upper part of the saw blade is
covered, e.g. by the guard.
• Do not use the guard for handling or transportation.
• Do not remove the saw bench table when adjusting the riving knife.
This information replaces the information of the instruction manual.
The following factors are of influence to noise production:
– the material to be cut
– the type of saw blade
– the feed force
Residual risks
The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
B&D_59