Setting The Dmx Start Address; Using Subaddresses; Additional Functions; Key Lock - IMG STAGELINE ODW-2410RGBW Manual De Instrucciones

8.3 Setting the DMX start address

For control of the floodlight by means of a light
controller, the DMX start address for the first
DMX channel must be set . If, for example, the
address 17 is to be used for controlling the
function of the first DMX channel, set the start
address at the ODW-2410RGBW to 17 . All other
DMX channels of the ODW-2410RGBW will be
automatically assigned to the subsequent ad-
dresses . The following table is an example with
the start address 17:
Number
DMX addresses
of DMX
assigned
channels
3 17 – 19
4 17 – 20
5 17 – 21
6 17 – 22
11 17 – 27
Fig. 5 DMX address assignment for start address 17
1) Call up the menu item
2) The current DMX start address will appear
on the display, e . g .
Addr:001
3) Use the button UP or DOWN to set the start
address .

8.3.1 Using subaddresses

In the 11-channel mode (
ter 8 .2), subaddresses may be used to inde-
pendently control up to 66 floodlights (floodlight
groups) one after the other via a single DMX
start address . Thus, the maximum number of
DMX units possible is substantially increased .
DMX channel 11 is used to select floodlights
with a subaddress .
Floodlights having the same start address
and different subaddresses may be controlled
in sync if DMX channel 11 is set to a DMX value
less than 11 .
1) Call up the menu item
menu .
ID
2) Use the button UP or DOWN to activate the
use of subaddresses (
dressing is deactivated (
will ignore the data for channel 11 .
3) Use the button MENU to return to the main
menu, and then call up the menu item
.
Address
4) Use the button UP or DOWN to assign a sub-
addresss (1 – 66) to the floodlight .
To be able to operate the floodlight, set the DMX
channel 11 at the light controller to the DMX
value that corresponds to the subaddress of the
floodlight ( ☞ chapter 10 .1 .7, second table) .
12
9
Note: To be able to control the floodlight by DMX
after one of the settings described in this chapter has
been made, call up one of the following menu items:
RUN: DMX
DMX Address
Personality
ID Address

9.1 Key lock

Next possible
A key lock may be used to protect the flood-
start address for the
light against unauthorized operation . When the
subsequent DMX unit
key lock is activated, settings can only be made
20
after a specific sequence of buttons has been
21
pressed .
22
1) Call up the menu item
23
28
2) Use the button UP or DOWN to activate the
When
.
DMX Address
function will be active as soon the display illu-
mination extinguishes . To operate the floodlight
.
with the key lock activated:
1) Press the button ENTER so that
2) Press the following buttons:
, ☞ chap-
Stage
3) The floodlight can now be operated as usual .

9.2 Limiting colours

A maximum value can be defined for the bright-
and the sub-
SET
ness of the colours red, green and blue . Thus, it
is, for example, possible to compensate differ-
ences to other floodlights if they are controlled
) . When subad-
together with the ODW-2410RGBW . The colour
ID Ɗon
), the floodlight
limitation will apply to both independent and
off
DMX-controlled floodlight operation .
1) Call up the menu item
ID
2) Set the following maximum values:
3) The arrow
To define if the limitation values set are to be
applied:
4) Use the button MENU to return to the main
5) Use the button UP or DOWN to activate the

Additional Functions

KEY LOCK
key lock ( n) or to deactivate it (
KEY Ɗo
n has been selected, the key lock
KEY Ɗo
appears on the display .
UP, DOWN, UP, DOWN, ENTER
For each of the first four buttons pressed, an
asterisk will appear on the display .
*
The key lock, however, will be active again
when the display illumination extinguishes
(unless the key lock has been deactivated by
means of the menu item
KEY LOCK
CAL2 Parameter
and the submenu .
REGW
brightness of red
ƊRed :
brightness of green (0 – 255)
green:
brightness of blue
blue :
always precedes the current
Ɗ
selection or the value to be set . To set the
parameter selected: Press the button ENTER
and use the button UP or DOWN to change
the setting; then press the button MENU
to return to the parameter selection and to
change another parameter .
menu, then call up the menu item
the submenu .
REGW
colour limitation function ( ) or to deacti-
on
vate it ( ) .
off

9.3 Artificial response time of the LEDs

LEDs almost instantly respond to changes in
brightness setting . To simulate the response time
of conventional lamps, four different levels of
artificial response time are available for DMX
control . For the DMX operation mode
make this setting by means of DMX channel 10
(chapter 10 .1 .7) . For the other DMX operation
modes, proceed as follows:
1) Call up the menu item
menu
Dim
2) Use the button UP or DOWN to select the
response time level (
the artificial response time (
9.4 Resetting the floodlight
to its factory settings
.
The factory settings of the floodlight are as follows:
Function
) .
off
Colour floodlight
beam
Static Color
Show programs
Auto
Master / slave
Password:
mode
RUN
DMX start address
DMX Address
DMX channels
Personality
Subaddress
ID Address
Subaddress
function

SET ID
) .
Colour limitation
function

SET REGW
LED response time
function

SET Dim
11 shades
of white
CAL1 white
(0 – 255)
(0 – 255)
Colour limitation
CAL2
Parameter
Key lock
KEY LOCK
Fig. 6 Reset values
To reset the floodlight to its factory settings:
1) Call up the menu item
.
REST
Password:
and
SET 2) Press the following buttons:
UP, DOWN, UP, DOWN .
For each press of a button, an asterisk * will
appear on the display .
3) Use the button ENTER to start the reset .
Stage
and the sub-
SET
.
... ) or to deactivate
1 4
) .
off
Factory setting
= 255, = 255,
Red green
= 255, = —,
blue white
= 00
strob
Aut.01
Slave
Addr: 001
(10/11 channels)
Stage
Addr:01
off
off
off
Storage location:
red, green, blue, white
: 255, 220, 5, 227
WT01
: 242, 222, 5, 227
WT02
: 255, 255, 61, 255
WT03
: 255, 255, 103, 255
WT04
: 255, 255, 130, 255
WT05
: 255, 255, 138, 255
WT06
: 255, 255, 153, 255
WT07
: 255, 255, 167, 255
WT08
: 255, 255, 180, 255
WT09
: 255, 255, 185, 255
WT10
: 255, 255, 202, 255
WT11
= 255,
REGW Red
= 255, = 255
green blue
KEY off
and the submenu
SET
appears on the display .
,