Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
DMX LED Floodlight
These instructions are intended for the installer
of the floodlight and for operators without any
technical training . Please read these instructions
carefully prior to installation and keep them for
later reference .
All operating elements and connections
described can be found on the fold-out page 3 .
Contents
1
Operating Elements and Connections
. . . . . . . . . . . . . . 9
2
Safety Notes
. . . . . . . . . . . . . . 9
3
Applications
4
Installation
. . . . . . . . . . . . . . 9
. . . . . . . . 10
5
. . . . . . . . . . . . . . 10
6
. . . . . . . . 10
7
. . . . . . . 10
. . . . . . . . . . 11
8
. . . . . . . . . . . . 11
. . . . . . . . . . 12
9
. . . . . . . . . 12
. . . . . . . . . . . . . . . 12
. . . . . . . . . . . . 12
. . . . . . . . . . . . 13
. . . . . . . . . . . . 13
. . . . . . . 13
. . . . . . . . . . . . 13
1
Operating Elements and
Connections
1 Tiltable floodlight head
2 Setscrews for the floodlight head
3 Holes (⌀ 11 .5 mm) to fasten two clamps
or C hooks for mounting the floodlight to
lighting stand systems
4 Buttons to select the operation mode and
to change settings
5 Display
6 Plug of the cable DMX IN for the DMX signal
. . 9
input:
Using the cable fitted with the XLR plug (10),
either connect the plug to a light controller
or to the DMX signal output of another DMX
controlled unit
7 Plug of the cable POWER IN for power sup-
ply (230 V/ 50 Hz):
. . . . . . 10
Either connect the plug to the mains socket,
using the cable fitted with the mains
plug (11), or connect it to the inline jack
of the cable POWER OUT (8) of another
ODW-2410RGBW
. . . . . 10
8 Inline jack of the connection POWER OUT for
power supply of another ODW-2410RGBW
9 Inline jack of the connection DMX OUT:
DMX signal output for connection to
. . 10
the DMX signal input of another ODW-
2410RGBW or another DMX-controlled unit
. . . . 10
via the adapter cable supplied
10 XLR plug of the DMX signal input
pin 1 = ground, pin 2 = DMX−, pin 3 = DMX+
. . . . . . 11
11 Mains plug for connection to a mains socket
(230 V/ 50 Hz)
. . . 11
2
Safety Notes
. . . . . 11
The unit corresponds to all relevant directives of
. . . . . . 12
the EU and is therefore marked with
WARNING The unit uses dangerous mains
•
Do not operate the unit and immediately dis-
. . . . 12
connect it from the mains
1 . if the unit or the mains cable is visibly dam-
12
aged,
2 . if a defect might have occurred after the
unit was dropped or suffered a similar ac-
cident,
. . . . . . 13
3 . if malfunctions occur .
In any case the unit must be repaired by skilled
personnel .
•
. . . . . . 13
A damaged mains cable must only be replaced
by skilled personnel .
. . . . . . 13
•
Never pull the mains cable for disconnecting
. . . . . . 13
the mains plug from the socket, always seize
the plug .
. . . . . . 13
•
For cleaning the floodlight housing and the
protective pane in front of the LEDs, only use
a mild detergent .
•
No guarantee claims for the unit and no li-
ability for any resulting personal damage or
material damage will be accepted if the unit
is used for other purposes than originally
intended, if it is not safely mounted or not
correctly operated, or if it is not repaired in
an expert way .
.
voltage . Leave servicing to skilled
personnel only; inexpert han-
dling of the unit may result in
electric shock .
•
Important for U. K. Customers!
The wires in this mains lead are coloured in
accordance with the following code:
green / yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1 . The wire which is coloured green and yel-
low must be connected to the terminal in
the plug which is marked with the letter
E or by the earth symbol
green or green and yellow .
2 . The wire which is coloured blue must be
connected to the terminal which is marked
with the letter N or coloured black .
3 . The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red .
Warning - This appliance must be earthed.
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which will not be
harmful to the environment .
3
Applications
This LED floodlight is used for effect illumination .
The floodlight features a weatherproof alumin-
ium housing (IP 66) and is therefore also suitable
for outdoor applications . 24 extra bright LEDs
are used as a light source . The LEDs can emit
light in the three primary colours (red, green
and blue) and in white as well as coloured light
created from additive colour mixing . Crossfading
from one colour to another and stroboscope
effects are also supported . The floodlight is de-
signed for control via a DMX light controller
(optionally 11, 10, 6, 5, 4 or 3 DMX control
channels) . However, it can also be operated on
its own without a controller .
As a special feature, the floodlight supports
66 subaddresses when used in DMX mode with
11 channels . Thus, it is possible to independently
control up to 66 floodlights (floodlight groups)
via a single DMX start address and the maxi-
mum number of DMX-controlled units possible
is substantially increased .
4
Installation
•
Always position the floodlight in a way
that ensures sufficient air circulation during
operation .
•
Always keep a minimum distance of 50 cm to
the object illuminated and to the adjoining
walls .
WARNING
Install the floodlight safely and
expertly .
1 . Place the floodlight on its rubber feet . To align
the floodlight, loosen the two setscrews (2) .
Tilt the floodlight head (1) as desired and then
retighten the screws .
2 . As an alternative, the floodlight can be
mounted to a lighting stand system: Use
two mounting clamps or stable C hooks to
fasten the floodlight via the two 11 .5 mm
holes (3) at the lateral brackets to a cross bar,
for example .
, or coloured
9
Publicidad
Capítulos
Tabla de contenido
