Publicidad
Idiomas disponibles
Idiomas disponibles
3) Press the button ENTER: The last program
GB
(
,
displayed. Select the desired program from the
three programs with the button UP or DOWN.
4) To change the speed, press the button ENTER:
The present speed is displayed. Select the
desired speed from the 9 speeds
with the button UP or DOWN.
7.2 Music control
For music-controlled run of the light show, it is pos-
sible to select three music modes, Sound 1 to
Sound 3:
Sound 1:
music-controlled stroboscope
Sound 2 and Sound 3:
music-controlled start of programs
Note: The music modes correspond to the three music
modes which can be activated in case of DMX control
(
chapter 8.4, table 7).
1) Press the button MENU / ESC so many times
until the main menu is reached.
2) Select the option
button UP or DOWN.
3) Press the button ENTER: The last music mode
adjusted (
displayed. Select the desired mode from the
three modes with the button UP or DOWN.
4) Turn up clockwise the control SENSITIVITY (6)
for the sensitivity of the microphone MIC (5) so
that the light effect panel responds to the music
as desired. When changing the volume at the
music system, also the sensitivity of the micro-
phone must be adapted accordingly. If the music
control should not function in an optimum way in
spite of the sensitivity control completely turned
up, increase the volume or reduce the distance
between the sound source and the panel.
7.3 Colour floodlight operation
For a constant lighting of the light effect panel in
one colour it is possible to select nine preset
colours and a colour to be adjusted individually:
1) Press the button MENU / ESC so many times
until the main menu is reached.
2) Select the option
button UP or DOWN.
3) Press the button ENTER: The last colour mode
adjusted (one of the preset colours
or the individual colour adjustment
vated and is displayed. Select the desired colour
mode from the colour modes with the button UP
or DOWN.
14
or
) adjusted is activated and
in the main menu with the
or
) is activated and
,
in the main menu with the
Individual colour adjustment
In the colour mode "ATF" the brightness of the
red, green and blue LEDs can separately be
adjusted:
a) If
ENTER. The display shows the last LEDs
adjusted: the red (
to
blue (
b) Select the LEDs with the button DOWN or UP
and press the button ENTER. The display
now shows the letter for the corresponding
colour of the LEDs ( ,
ness value (0 ... 255).
c) Adjust the desired brightness with the button
UP or DOWN.
d) Exit the menu item with the button MENU/
ESC. Now the next LEDs (
can be adjusted.
Hint: When adjusting the brightness of the red, green
or blue LEDs, not only their brightness changes but
also the shade of colour in case the colours are mixed.
Therefore, first adjust the colour which is to dominate to
the desired brightness and then add the other two
colours. If the intended colour mixture is white, first
adjust the brightness of the green colour because this
appears to be the brightest colour to the human eye.
Then add red to result in yellow and finally add blue to
result in white.
7.4 Master / slave mode
Several units RGBL-112DMX may be operated in
sync. Then the first unit (master unit) controls the
remaining units (slave units). Connect the units
with each other in a chain. For this purpose see
chapter 8.1, however, skip step 1.
Adjust the master unit (the first unit of the chain
of which the control input is not connected) to auto-
matic mode, music control or colour floodlight oper-
ation (
chapter 7.1, 7.2 or 7.3). Adjust the slave
units to the slave mode as follows:
1) Press the button MENU / ESC so many times
until the main menu is reached.
2) Select the option
button UP or DOWN.
3) Press the button ENTER: The slave mode is
activated, the display shows
the slave unit receives control signals from the
master unit, a point flashes on the display.
...
) is acti-
has been selected, press the button
), green (
) LEDs.
or ) and its bright-
) can be selected and their brightness
in the main menu with the
) or
or
,
. As soon as
Publicidad
