Preparations For Use - REMS Tiger Instrucciones De Servicio

eng
Right-angled sawing with REMS Akku-Tiger 22 V VE:
With guide holder 563000 and
REMS special saw blade 561001, 561007
Pipes (also plastic jacketed)
Hand-guided sawing with all REMS reciprocating saws
REMS universal saw blades and REMS saw blades
Steel pipes and other metal profi les,
Wood, wood with nails, pallets,
building materials, plastics
1.4. Number of strokes (idling speed)
REMS Tiger
REMS Tiger VE (infi nitely variable)
REMS Tiger SR (infi nitely variable)
REMS Tiger pneumatic (infi nitely variable)
REMS Akku-Tiger 22 V VE (infi nitely variable)
REMS Puma VE (infi nitely variable)
REMS Cat VE (infi nitely variable)
REMS Akku-Cat 22 V VE (infi nitely variable)
1.5. Electric data
REMS Tiger VE,
REMS Cat VE 230 V~; 50 – 60 Hz; 1050 W; 5 A or
110 V~; 50 – 60 Hz; 1050 W; 10 A
protective insulation, radio interference suppression
REMS Tiger SR 230 V~; 50 – 60 Hz; 1400 W; 6.4 A or
110 V~; 50 – 60 Hz; 1400 W; 12.8 A
protective insulation, radio interference suppression
REMS Puma VE 230 V~; 50 – 60 Hz; 1300 W; 6 A
protective insulation, radio interference suppression
REMS Akku-Cat 22 V VE 21.6 V – ---; 5.0 A
REMS Akku-Tiger 22 V VE 21.6 V – ---; 9.0 Ah
Rapid-charger Input
Li-Ion 230 V, 90 W Output
protective insulation, radio interference suppression
1.6. Compressed-air supply REMS Tiger pneumatic
Required working pressure
Air consumption at idling speed
Air consumption at full speed
Tube width
Oiler adjustment
1.7. Dimensions
REMS Tiger
REMS Tiger VE
REMS Tiger SR
REMS Tiger pneumatic
REMS Akku-Tiger 22 V VE
(with battery)
REMS Puma VE
REMS Cat VE
REMS Akku-Cat 22 V VE
(with battery)
1.8. Weights
REMS Tiger
REMS Tiger VE
REMS Tiger SR
REMS Tiger pneumatic
REMS Akku-Tiger 22 V VE, without battery
REMS Puma VE
REMS Cat VE
REMS Akku-Cat 22 V VE, without battery
REMS Battery Li-Ion 21.6 V, 5.0 Ah
REMS Battery Li-Ion 21.6 V, 9.0 Ah
Guide support ⅛" – 2"
Guide support 2½" – 4"
Guide support 5" – 6"
1.9. Noise information
Sound pressure level L
pA
REMS Tiger/Cat
REMS Puma
Sound capacity level L Sound capacity level L Sound capacity level L
WA WA
REMS Tiger/Cat
REMS Puma
Uncertainty K
1.10. Vibrations
Weighted effective value of acceleration:
all REMS reciprocating saws
Sawing chipboard 18.3 m/s²
Sawing wooden beam 28.3 m/s²
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
⅛" – 2"
Ø ≤ 6", ≤ 250 mm
≤ 250 mm
2400 min‫¹־‬
0 ... 2400 min‫¹־‬
700 ... 2200 min‫¹־‬
0 ... 1700 min‫¹־‬
0 ... 1900 min‫¹־‬
0 ... 2800 min‫¹־‬
0 ... 2400 min‫¹־‬
0 ... 1900 min‫¹־‬
– ---; 5.0 A – h; 21.6 V – ---; 9.0 Ah
100 – 240 V~; 50 – 60 Hz; 90 W
21.6 V – ---
0.6 MPa, 6 bar (85 psi)
1.6 m³/min (56 cf/min)
1.3 m³/min (46 cf/min)
12 – 13 mm (½")
6 – 7 drops/min
455×80× 90 mm (17.9"×3.2"×3.5")
435×80×135 mm (17.1"×3.2"×5.3")
490×80× 90 mm (19.3"×3.2"×3.5")
445×80× 90 mm (17.5"×3.2"×3.5")
405×83×230 mm (15.9"×3.3"×9.1")
475×90×152 mm (18.7"×3.5"×6.0")
435×80×135 mm (17.1"×3.2"×5.3")
405×83×205 mm (15.9"×3.3"×8.1")
3.0 kg (6.6 lb)
3.0 kg (6.6 lb)
3.1 kg (6.8 lb)
3.8 kg (8.4 lb)
2.3 kg (5.1 lb)
3.8 kg (8.4 lb)
3.0 kg (6.6 lb)
2.3 kg (5.1 lb)
0.8 kg (1.8 lb)
1.1 kg (2.4 lb)
1.0 kg (2.2 lb)
1.7 kg (3.7 lb)
2.7 kg (6.0 lb)
96 dB(A)
87 dB(A)
107 dB(A)
98 dB(A)
K = 3.3 m/s²
K = 2.4 m/s²
CAUTION CAUTION
The indicated weighted effective value of acceleration can differ during operation
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual conditions of use (periodic duty) it may be necessary
to establish safety precautions for the protection of the operator.

2. Preparations for Use

2.1. Electrical connection
Note the mains voltage! Before connecting the REMS reciprocating saw or the
rapid charger, check whether the voltage given on the rating plate corresponds
to the mains voltage. On building sites, in a wet environment, indoors and outdoors
or under similar installation conditions, only operate the power tool on the mains
with a fault current protection switch (FI switch) which interrupts the power supply
as soon as the leakage current to earth exceeds 30 mA for 200 ms.
Rechargeable batteries (Fig. 1 (13))
T Total discharging by undervoltage Total discharging by undervoltage
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by "total discharge", see graduated charging
state display. The cells of the REMS Li-Ion battery are delivered pre-charged
to approx. 40 %. Therefore the Li-Ion batteries must be charged before use
and recharged regularly. Failure to observe this regulation of the cell manufac-
turer can lead to damage to the Li-Ion battery by total discharging.
Total discharging due to storage
If a relatively low charged Li-Ion battery is stored, self discharging can lead to
total discharge damage of the battery after longer storage. Li-Ion batteries must
therefore be charged before storing and recharged every six months at the
latest and charged again before use.
NOTICE NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid
their total discharge. The rechargeable battery will be damaged by total
discharge.
Only use a REMS rapid charger for charging. New Li-Ion batteries and Li-Ion
batteries which have not been used for a long time only reach full capacity after
several charges. Non-rechargeable batteries may not be charged.
Machine status check, REMS Akku-Tiger 22 V VE, REMS Akku-Cat 22 V
VE
The cordless reciprocating saw is equipped with an electronic machine status
check (Fig. 1 (17)) by a 2-coloured green/red LED. The LED lights green when
the battery is fully or still suffi ciently charged. The LED lights red when the
battery must be charged. If this status occurs during sawing, the sawing must
be completed with a charged Li-Ion battery. The LED lights red and the cord-
less reciprocating saw switches off if overloaded. After a short dwell time, the
LED lights green again and sawing can be continued. The LED fl ashes red if
the motor temperature has been exceeded. After a cooling time, the LED lights
green again and sawing can be continued. The cooling time is reduced when
the cordless reciprocating saw is operated in idle mode. The LED lights red if
an impermissible battery has been inserted.
If the cordless reciprocating saw is not being used, the LED goes out after
approx. 2 hours but comes on again when the cordless reciprocating saw is
switched back on.
Graduated charging state display (18) of the Li-Ion 21.6 V battery
The graduated charging state display shows the charging state of the battery
with 4 LEDs. At least one LED lights for a few seconds after pressing the key
with the battery symbol. The more LEDs that light green, the higher the charging
state of the battery. If a LED fl ashes red, the battery must be charged.
Rapid charger Li-ion (Art. No. 571585)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the REMS rapid charger, the green control
lamp fl ashes to indicate that the battery is charging. The green light stops
fl ashing and remains on to signal that the battery is fully charged. If the red
control lamp fl ashes, the battery is defective. If the red control lamp comes on
and remains on, this indicates that the temperature of the rapid charger and /
or the battery is outside the permissible range of 0°C to +40°C.
NOTICE NOTICE
The rapid charger is not suitable for using outdoors.
2.2. Sawing with guide holder (2) (right-angled sawing)
3 dB(A)
WARNING WARNING
Pull out the mains plug or remove the battery before fi tting/removing the
guide holder!
Push the bearing pin (3) of the guide holder (2) into the REMS reciprocating
saw/REMS cordless reciprocating saw from the side so that the limit pin of the
guide holder runs in the longitudinal slit of the REMS reciprocating saw.
NOTICE NOTICE
The guide holder must be used to achieve right-angled saw cuts because
exact right-angled positioning and guiding of the REMS reciprocating saw/
REMS cordless reciprocating saw is not possible by hand.
eng
13