Setting The Unit Into Operation; Power Supply; Independent Operation; Automatic Programs - IMG STAGELINE RGBL-222DMX Manual De Instrucciones

to emit coloured light in the three primary colours
(red, green and blue) and light created by additive
colour mixing of the primary colours.
The unit is designed for control via a DMX light
controller (6 DMX control channels); however, it is
also suitable for independent operation without a
controller.

4 Setting the Unit into Operation

4.1 Installation
Fasten the light effect panel via its two mounting
brackets (6) at a suitable place. To adjust the direc-
tion of the beam, release the locking screws on
the brackets, adjust the desired inclination, then
retighten the screws.

4.2 Power supply

WARNING To prevent damage to your eyes,
never look directly into the light
source for a long time.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
Connect the plug (9) of the cable POWER IN to the
inline jack of the supplied cable with mains plug (7).
Secure the connector with the cap nut. Connect the
mains plug to a socket (230 V~ / 50 Hz). Thus, the
light effect panel is switched on. For a few seconds,
the display (2) shows the last function selected
(fig. 3) before it is deactivated. To switch off, dis-
connect the mains plug from the socket.
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket
which is switched on and off via a light switch.
CAUTION!
1. Never connect the unit to the mains voltage via
a dimmer.
2. Make sure that the inline jack of the cable is
weatherproof when the unit is used for outdoor
applications and no further unit is connected to
the cable POWER OUT (4). The inline jack car-
ries mains voltage.
4.2.1 Connecting several light effect panels
When several RGBL-222DMX panels are used,
they can be interconnected for power supply. For
the time being, do not yet connect the first light
effect panel to a mains socket; the connection
cables must not carry any mains voltage yet.
1) Connect the first unit via the inline jack of the
cable POWER OUT (4) to the plug (9) of the
cable POWER IN of the second panel. Secure
the connector with the cap nut. Proceed in the
same way to connect the second panel to the
third panel etc. until all panels have been con-
nected in a chain.
If the mains connection cables between the
panels are too short, use suitable extension
cables (e. g. ODP-34AC from "img Stage Line"
of 2 m length).
WARNING The total current in the connection
cables (4, 9) must not exceed
10 A, otherwise a cable fire may
occur due to overload. Therefore,
only interconnect 28 light effect
panels as a maximum.
2) For outdoor installation, the inline jack of the
cable POWER OUT (4) on the last cable must
be weatherproof. The inline jack carries mains
voltage.
3) Finally connect the mains plug of the first panel
to a socket (230 V~ / 50 Hz).
5 Operation
The control buttons A and B (3) are used to select
the operating mode and various functions. Figure 3
on page 3 shows the way the modes and functions
are indicated on the display (2). Approximately
30 seconds after you have pressed a button, the
display is deactivated so that it will not bother you.
When you press a button, it lights up again.

5.1 Independent operation

For independent operation, press the control but-
tons (3) to select the desired mode as follows:

5.1.1 Automatic programs

Two automatic programs with adjustable speed are
available:
= crossfading between different colours
= stroboscope
1) When the display (2) is not activated, press one
of the control buttons (3).
2) Press both control buttons A and B at the same
time so that the display starts flashing.
3) Press the button A or B repeatedly until the dis-
play shows or
4) Press both control buttons A and B at the same
time again so that the display stops flashing.
5) Press the button A or B to switch between the
two programs.
.
GB
9