Before Starting The Machine; Setting The Cutting Height; Fuel And Oil; Operation - Hurricane HBS 75 Manual De Instrucciones

Anleitung_HBS_75_SPK7:_
GB

6. Before starting the machine

Check that all moving parts move smoothly before
you start using the machine. Check that all screw
connections are securely fastened and also check all
the safety devices.

6.1 Setting the cutting height

Fit the carrying strap as shown in Figures G1 –
G3.
Hook the machine to the carrying belt (Fig. G4).
Adjust the perfect working and cutting position
using the various strap adjusters on the carrying
strap (Fig. G5).
In order to establish the optimum length of the
carrying strap, you should then make a few
swinging movements without starting the engine
(Fig. H).
The carrying strap is fitted with a quick-release
mechanism. Pull the red strap section (Fig. G6) if you
need to remove the strap quickly.
Important: Always use the strap when working with
the machine. Attach the strap as soon as you have
started the engine and it is running in idle mode.
Switch off the engine before you take off the carrying
strap.
Check the machine for the following each time before
use:
That there are no leaks in the fuel system
That the cutting unit and all safety devices are in
perfect condition
That all screws are securely fastened

6.2 Fuel and oil

Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
manufacturer's engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bottle).
Then shake the bottle well.
20
27.11.2008 11:37 Uhr Seite 20
6.3 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
1 liters
2 liters

7. Operation

Please note that the statutory regulations governing
noise abatement may differ from town to town.
7.1 Starting the engine when cold
Fill the tank with the required amount of oil/petrol mix.
See "Fuel and oil".
1. Set the machine down on a hard, level surface.
2. Set the choke lever (Fig. A/Item 10) to "
3. Press the fuel pump (primer) (Fig. A/Item 16) 10
times.
4. Switch the ON/OFF switch (Fig. A/Item 6) to "I".
5. Secure the throttle lever. To do so, actuate the
throttle lock (Fig. A/Item 7) and then actuate the
throttle lever (Fig. A/Item 8) while pressing the
locking button (Fig. A/Item 9) at the same time to
secure the throttle lever.
6. Hold the machine firmly and pull out the starter
cable (Fig. A/Item 11) until you feel it start to
resist. Then tug sharply on the starter cable 4
times. The machine should start.
Please note: Never allow the starter cable to
snap back. This may damage the machine.
7. Once the engine has started, move the choke
lever immediately to " " and allow the machine
to warm up for approx. 10 seconds.
Please note: Since the throttle lever is secured,
the cutting tool starts to operate when the engine
is started.Then release the throttle lever by simply
actuating it (the engine then returns to running in
idle mode).
8. If the engine does not start up, repeat steps 6-7
above.
Please note: If the engine does not start up even
after several attempts, read the section "Engine
Troubleshooting".
Please note: Always pull the starter cord out in a
straight line. If it is pulled out at an angle, then friction
will occur on the eyelet. As a result of this friction, the
cable will become frayed and will wear away faster.
Always hold the starter handle when the cable
retracts. Never allow the cable to snap back when it
has been pulled out.
Petrol 2-stroke oil
25 ml
125 ml
".