Intended Use; Inserting/Replacing The Battery; Technical Data - Bosch GLL 2-15 Instrucciones De Funcionamiento Y Seguridad

The tool is intended for determining and checking horizontal and vertical lines.
Inserting/Replacing the Battery
Use only alkaline batteries.
To open the battery lid 8, press the latch of
the battery lid 7 in the direction of the arrow
and remove the battery lid. Insert the supplied
batteries.
When inserting, pay attention to the correct
polarity according to the representation on the
inside of the battery compartment.
The numbering of the product features shown
refers to the illustration of the tool on the graphic
page.
1 Exit opening for laser beam
2 Tripod mount 1/4-20
3 On/Off switch
4 Operating mode button
5 Laser warning label
6 Serial number
7 Latch of battery lid
8 Battery lid
9 Positioning device
10 Mounting screw for positioning device
11 Swiveling disc to move laser left to right
Article number . . . . . . . . . . . . 3 601 K63 713
Working range, min.
Levelling Accuracy: . . . . . . up to ± 1/8in @ 33ft
Self-levelling range, typically . . . . . . . . . . . . ±4°
Levelling duration, typically . . . . . . . . . . . . . <4s
Operating temperature . . . . . . . .14° F to 122° F
Storage temperature . . . . . . . . . -4° F to 158° F
Relative air humidity, max . . . . . . . . . . . . . 90 %
Laser class . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Laser type . . . . . . . . . . . . . . . . . 635 nm, <1mW
Mount threading . . . . . . . . . . . . . . . . . . . . 1/4-20
1)
The working range can be decrease by unfavorable environmental conditions (e.g. direct sun irradiation)
1)
. . . . . . . . . . . . .50ft (15m)
± 3mm @ 10m
(–10° C to +50° C)
(–20° C to +70° C)
Intended Use
Preparation
When the batteries become weak, the laser
beams flash rapidly for 5 s every 10 minutes.
Always replace all batteries at the same time.
Only use batteries from one brand and with the
identical capacity.
• Remove the batteries from the tool
w hen not using it for extended
p eriods. When storing for extended
periods, the batteries can corrode
and discharge themselves.
Features
12 Fine adjustment knob
13 Ceiling grid clip
14 Magnets
15 Retractable feet
16 Screw hole for positioning device
17 Laser viewing glasses*
18 Laser target plate
19 Tripod* (BS 150)
20 Telescopic pole system* (BP 350)
21 Self-leveling indicator
22 Protective carrying case
*The accessories illustrated or described are
not included as standard delivery.
Technical Data
C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
6
Batteries . . . . . . . . . . . . . . . . . . . . . 3 x AA 1.5V
Operating lifetime, approx. . . . . . . . . . . . . . .15 h
Automatic switch-off after approx. . . . . . . . 2 hr
Weight . . . . . . . . . . . . . . . . . . . . . . 1/2lb (0.25kg)
Dimensions . . . . . . . . . . . 3-1/8" x 1-5/8" x 3-3/4"
The tool can be clearly identified with the serial
number 6 on the type plate.
-8-
(80 x 42 x 96mm)