Declaration Of Conformity - Narex EKK 31-QS Instrucciones De Uso

Ocultar thumbs

página de 40

/ 40
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

Drilling into Tiling

First, slowly drill into the tile without the hammer action turned on.

Once you have drilled through the tile, switch to the impact drilling set‑

ting and drill away the underlying material.

Screwing

Driving bits can be mounted into the fastening head with chuck (7b)

or directly into another suitable adapter with SDS‑Plus fastening shank.

Long‑term Storage

After the device has been stored for an extended period of time, it

may not operate at full capacity right from the start when in impact

drilling mode. It is a common problem caused by hardened lubricant

in the impact drilling mechanism. Leave the device in impact drilling

mode and keep it running until the impact drilling mechanism warms

up sufficiently.

If you still have any issues after this, please contact an authorised repair

centre.

Maintenance and Service

Attention! Risk of injury by electric current. Unplug the de‑

vice from the power socket before making any adjustments

(such as mounting or removing hand grips, making adjust‑

ments, replacing drill bits, etc.)!

‰ Always keep the air holes (13) clean.

‰ Regularly clean the plastic parts accessible from the outside with a

cloth without the use of detergents.

‰ After having used the device in demanding conditions for a longer

period of time, you should take the device for a service inspection

and thorough cleaning to a Narex authorised service centre.

‰ The device is fitted with self‑disconnecting carbon brushes. If the

brushes are worn down, the motor turns off automatically. This pre‑

vents damaging the rotor. The carbon brushes can only be replaced

by an authorised service centre.

The device must undergo maintenance at regular intervals after

every ca 100 hours of use to guarantee good and constant opera‑

tion and long service life.

Regular maintenance involves the following steps:

‰ Cleaning the motor box, removing any sediments, dirt and dust

from the box.

‰ Cleaning the fastening hub.

‰ Checking the wear on the piston rings.

‰ Checking the wear on the carbon brushes.

‰ Replacing the grease fillings.

‰ Making sure the safety clutch is working correctly.

Attention! With the principles of protection against injury

by electric current and the protection rating of the device

in mind, all maintenance and service work that requires the

removal of the machine's casing must be done only by an author‑

ised service centre!

You can find the current list of authorised service centres on our website

at www.narex.cz in the "Service Points" section.

Accessories

Accessories recommended for use with this device are commonly avail‑

able consumer accessories and can be purchased in shops selling elec‑

trical hand tools.

Storage

If stored packaged, the device can be stored in a dry storehouse without

heating if the temperature inside does not drop below ‑5 °C.

If stored unpackaged, the device can only be stored in a dry storehouse

where the temperature does not drop below +5 °C and where there

aren't any sudden changes in the temperature.

Recycling

Electrical tools, accessories and packaging should all be submitted for

reuse to prevent environmental damage.

EU countries only:

Do not put electrical tools into household waste!

In accordance with European Directive 2002/96/EC on waste electrical

and electronic equipment and the directive's enforcement in national

laws, unusable electrical tools must be collected for reuse/recycling/

recovery to prevent environmental damage.

Warranty

Our devices come with a warranty for material or production defects

in accordance with the legal regulations of the given country, for a pe‑

riod no shorter than 12 months. In EU countries, the warranty period

is 24 months for exclusively private use (proven by an invoice or bill of

delivery).

Damage caused by natural wear and tear, overloading, improper han‑

dling, damage caused by the user or by use contrary to the operating

manual, or damage known already at the time of purchase is excluded

from the warranty.

Complaints can be accepted only if the device is sent back to the sup‑

plier or a NAREX authorised service centre in a non‑disassembled state.

Store and keep the operating manual, safety instructions, list of spare

parts and proof of purchase. Otherwise, the manufacturer's current war‑

ranty terms always apply.

Note

Based on constant research and development, the manufacturer re‑

serves the right to change the technical information stated here.