Campbell Hausfeld PL1574 Manual De Usuario

Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
BUILT TO LAST
Description
The 3-in-1 Woodworking Kit is
designed for cutting, sanding and
routing. The tool may be used with the
included accessories, or other
separately purchased cutout bits,
accessories and sanding drums. Using
the correct accessory you can cut, sand,
or grind a large assortment of
materials such as:
Building Materials – Acoustical tile,
cement board, ceramic, ceramic wall
tile, drywall, fiberglass, glass, hard
woods, marble, OSB, plaster,
shell/stone, stucco, underlayment
and wood composites.
Plastics – Acrylic, foam board,
laminates, vinyl siding.
Metals – Aluminum, brass, iron,
steel.
Safety Guidelines
This manual contains information that
is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Danger indicates
DANGER
!
an imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
Warning indicates
WARNING
!
a potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
Caution indicates a
CAUTION
!
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
Notice indicates
NOTICE
important
information, that if not followed, may
cause damage to equipment.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2002 Campbell Hausfeld/Scott Fetzer
3-in-1 Woodworking Kit
Adapter
Spindle
Collet Nut
FIgure 1
General Safety
Information
CALIFORNIA PROPOSITION 65
DANGER
!
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
WORK AREA SAFETY
Keep work area clean and well lighted.
Cluttered benches and dark areas invite
accidents.
Avoid
WARNING
!
a
dangerous environment.
Do not use air tools in the
presence of flammable
liquids or gases. Avoid
chemical or corrosive
environments.
This air tool is part of a
high-pressure air system.
Do not exceed the
maximum pressure rating
of this tool or any
component in the system.
Release all pressure from the system
For parts, product & service information
visit www.chpower.com
Throttle Safety Catch
Throttle
Throttle Screw
Exhaust
Attachment
Set Screw
before attempting to install, service,
relocate or perform any maintenance.
Keep bystanders, children and visitors
away while operating a power tool.
Distractions can cause you to lose focus
and control.
WARNING
!
and ear protection must
be worn during operation.
Everyone in the work area
must wear the proper
safety equipment. Grinding and cutting
produce sparks and airborne particles
which can cause serious personal
injury.Accessories can fail during use
causing serious personal injury. Use
ANSI/OHSA approved eye, hearing,
breathing, skin and head protection.
Do not overreach. Keep
proper footing and
balance at all times.
Proper footing and
balance enable better
control of the tool in
unexpected situations.
Never work around live electrical wires.
If you must cut into existing walls or
other blind areas where electrical
wiring may exist, disconnect all fuses or
circuit breakers feeding the work area.
Regulator
1/4" NPT
Inlet
Industrial
Plug
Safety
glasses
IN270401AV 11/02