Edge Guide - Campbell Hausfeld PL1574 Manual De Usuario

Operating Instructions
Operation
(Continued)
DRUM SANDING BITS
To attach the drum sanding bit:
Disconnect the air hose.
1. Remove any accessory that is in the
tool.
2. Insert drum sanding bit fully into the
collet.
3. Tighten collet nut.
4. The depth guide may or may not be
used depending on your application.
5. Slide drum sanding paper onto drum
sanding bit.
6. Using a 12 mm wrench, tighten drum
nut firmly by turning it in a
counterclockwise direction.
Throttle Screw
Drum Sanding Paper
Drum Sanding Bit
Figure 4
7. Check that all parts are tight and
safety equipment is in place before
turning on the tool.
8. Attach the air hose and begin
sanding.
NOTE: Do not try to use accessories
with 1/32", 1/16", or 3/32" diameter
shanks. Some 1/8"and/or 1/4" shank
high-speed router bits have large
cutting edges and should not be used
in this tool.
Do not use wire
CAUTION
!
brushes, bristle
brushes or polishing wheels in this
tool. These accessories are designed to
work on tools with a low RPM setting.
ROUTER BASE
Disconnect the air hose.
To attach the router base:
1. Remove the wingnut and washers
from the attachment set screw.
2. Insert the attachment set screw into
the router base guide slot.
3. Place flat washer on attachment set
screw, followed by lock washer and
www.chpower.com
then wingnut. Firmly finger tighten
wingnut.
Figure 5 - Router base attached to tool
To adjust the router base:
1. Loosen the wingnut by turning
counterclockwise.
2. Slide router base up or down to the
desired depth of your cut.
3. Turn wingnut clockwise to tighten.
4. Install desired accessory bit (and
collet, if necessary).
When using router to bevel edges,
Regulator
work in a left-to-right direction. Do not
try to remove a lot of material on the
first pass. Several passes are
recommended to prevent jumping or
binding.
TEMPLATE GUIDES
To attach template guide:
1. With the supplied Allen wrench,
remove the three (3) flathead screws
in the plastic bottom of the router
base.
2. Remove the plastic bottom and insert
the desired template guide, cylinder
down.
3. Replace the plastic bottom, insert
screws and tighten with Allen
wrench.
Plastic Bottom
Figure 6 - Template guide attached to
router base
When using template guides, work in a
left-to-right direction, ending your cuts
in a counterclockwise rotation. Use a
slow, steady, constant motion.

EDGE GUIDE

To attach edge guide:
1. Insert the open-ended slot of the
2. Remove the wingnut and carriage
3. Insert the carriage bolt through the
4. Put wingnut on carriage bolt and
Edge Rail
Figure 7 - Edge guide attached to
router base
To adjust edge guide:
1. Loosen other wingnut on the edge
2. Turn wingnut clockwise to tighten.
carriage bolt fits securely into the slot.
Improper assembly could lead to loose
attachments, which might cause
personal injury and/or damage to
workpiece.
cutting, sanding, or grinding with any
accessory. Never attempt to hold the
Router Base
work with one hand while using any of
these accessories. The accessory could
kick back or break, causing loss of
control and resulting in serious injury.
Storage
Template
Guide
The air tool must be lubricated before
storing. An air motor cannot be oiled
too often.
Flathead Screws
4
edge guide into the appropriate slot
in the router base.
bolt from the opposite end of the
edge guide.
bottom side of the router base.
tighten firmly.
Wingnut
Flat Washer
Edge Guide
Spacer
Wingnut
Flat Washer
guide and slide the edge rail to the
desired position.
Make sure the
CAUTION
!
square neck of the
Always clamp work
CAUTION
!
securely when
Carriage Bolt
Edge Guide