Tuner Operation; Direct Tuning - Jensen PHASE LINEAR Serie Manual De Instrucciones

Multimedia receiver
Ocultar thumbs Ver también para PHASE LINEAR Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

UV10

TUNER OPERATION

Tuner TFT Display
2
8
17
1
4
5
10
FM-1
P1 87.5 MHz
ST
LOC
PTY
RDS
RADIO
P1 87.5 MHz
E
Q
P2 90.1 MHz
P3 98.1 MHz
P4 106.1MHz
P5 107.9MHz
P6 102.9MHz
BAND
PS:
6
7
11
15
PTY
AS
2/2
LOC
16
25
23
1.
Current radio band indicator
2.
Radio frequency indicator
3.
Clock
4.
Stereo broadcasting indicator
5.
Strong Local signal broadcasting indicator
6.
Preset radio stations: Touch to recall preset stations
7.
Information about the current function
8.
EQ: Touch for quick access to Equalizer level settings
9.
: Touch to access the direct entry screen
10. Current preset station indicator
11. |<<: Touch to seek backward
12. >>|: Touch to seek forward
13. <<: Touch to tune backward one step
14. >>: Touch to tune forward one step
15. BAND: Touch to change between AM/FM bands
16. 1/2: Touch to view a second screen of menu choices
17.
: Touch to view the SOURCE MENU and select a new
playback source
18. MEM: View screen used to enter current channel into
9
3
19
preset memory
19.
: Touch to view the SETUP menu
20. PS (Preview Scan): Touch to scan all stations available,
01:02 PM
stopping for 5 seconds at each and continuing until a
station is selected
21. PTY Indicator
14
22. RDS Indicator
20
23. AS: Touch to automatically store stations
PS
12
24. PTY: Touch to activate the PTY function
25. LOC: Press to activate/deactivate the Local function
13
Switching to Radio Tuner Source
1/2
MEM
Touch the top left corner of the screen (the RADIO
circle) to view the SOURCE MENU. Touch "Radio".
16
18
Press the SRC button (10) on the front panel or remote
control (8) to switch to the AM/FM or RADIO source.
Selecting FM/AM Band
Touch the BAND button (15) on the screen, or press the ||>/
24
BAND button on the remote control (30) to change between
the following bands: FM1, FM2, FM3, AM1, and AM2.
NOTE: The BAND button on the unit only works when the
TFT is closed.
Seek Tuning
To seek the next higher station:
Touch the >>| button on screen.
Press the >>| button (19) on the remote control.
To seek the next lower station:
Touch the |<< button on screen.
Press the |<< button (17) on the remote control.
Manual Tuning
To increase or decrease the tuning frequency one step:
Touch the >> or << buttons on screen.
Press the >> or << buttons (14, 22) on the remote
control.

Direct Tuning

To enter a radio station directly, touch the
the GOTO button (21) on the remote control to display the
direct entry menu.
Enter the desired radio station using the on-screen number
pad. Press the Enter button to tune to the selected station. To
exit the screen without changing the station, touch Exit. To
clear your entry and start over, touch Clear.
Using Preset Stations
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the screen.
Storing a Station
1.
2.
3.
Recalling a Station
1.
11
button or press
FM: _ _ _ . _ MHz
1
2
3
Exit
4
5
6
7
8
9
Enter
0
Clear
Select a band (if needed), then select a station.
Touch the on-screen MEM button (18) to open the
preset screen.
Preset: _
P1 P2 P3
P4 P5 P6
E x i t
Touch the preset number in which you would like to
store the current station (or touch Exit to cancel and
close the menu). The preset number and station
appears highlighted.
Select a band (if needed).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Phase linear uv 10

Tabla de contenido