Electrical Connection - ADEO SCREEN ULTIFORMAT Manual De Uso

ENGLISH – Motorized screen user manual
Screens and their projection surfaces are delicate and must be cleaned with great care, according to the following instructions:
Never use solvents, chemical or abrasive products, or pointed tools to clean the surface.
Avoid contact with other materials (varnishes, inks etc) as they might be impossible to remove from the canvas.
FABRIC VISION, REFERENCE, HELIOS: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary.
Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning operations can cause electrostatic
charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being attracted again
GENERIC PROFILE: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary
VELVET PROFILE: Clean profile with a soft clean cloth, or a brush with soft, antistatic bristles. A vacuum-cleaner brush may be used, provided its bristles are soft and perfectly clean.
STRUCTURE and ANCHORING BRACKETS: The state of the product and the anchoring capacity of its brackets must be checked regularly. In case of canvas deformation or rips, or loosening of structural
components such as brackets or screws, action must be taken immediately to clear the area around the screen and avoid hazard to people and things, replace the defective component and restore the
product's functionality.
The type of motor installed on the product is identified by a label applied on each product showing the CE logo. When unwrapping the product please check the model type indicated on the label in order to
perform the installation and cable connections correctly. Should the power of the motor be different from that of the supply network of the installation place, please contact an electrician to have a current
and Hz transformer installed.
ELECTRICAL CONNECTION: electric cabling must be conformant with applicable IEC standards. IEC norm EN 60335-1 requires that supply network be fitted with an
omnipolar selector switch with contact opening distance of at least 3 mm.
For each motor (e.g. plug switch etc.). In case of need, this device ensures that the power supply is safely and quickly cut off.
Use the wires as described in the figure.
ATTENTION:
This product contains two motors, which must both be wired in the same manner.
WARNING: Correctly performed, state-of-the-art, norm-compliant electrical connections are important to prevent accidents and to ensure the screen's optimal and
unaltered performance over time. Prior to carrying out any operation on electrical parts ensure that power supply is disconnected.
Bus cables (black white orange) must be insulated if not used for the push-button command.
In screens fitted with cases the motor is positioned on the right-hand side of the screen as seen from the front.
Operates with standard radio control (supplied).
Connection for each motor:

RJ 9 cable (to connect
with ILT4 interface)

Power supply cable (to
connect with 230V)
12V Trigger
+ = 5  30V
G = Ground
Made by Adeo Screen sp. Z o.o. (Polska) Specifications are subject to change without notice. E&OE
Doc: MULTIFORMAT Installation Manual rev3 | 23.04.2013
Please verify that you are working with the latest revision of this document before specifying your screen.
06 CLEANING AND MAINTENANCE
ILT2 MOTOR TYPE IDENTIFICATION –CHARACTERISTICS – ELECTRICAL CONNECTION
IR Sensor
Motor characteristics
230V 50Hz:
Volt: 230V AC
Frequency: ~Hz50
Power: 90W
Torque: 6Nm
Speed: 17RpM
Max no. of cycles: 2
Operating T°: from –20 to +55 °C
Motor characteristics
120V 60Hz:
Volt: 120V AC
Frequency: ~Hz60
Power: 110W
Torque: 6Nm
Speed: 38RpM
Max no. of cycles: 2
Operating T°: from –20 to +55 °C
Interface characteristics
Power supplier:
90 ÷ 225 Vac 50/60 Hz
Protection class:
IP20 (of undamaged box)
Operating temperature:
0 ÷ 60 °C
Dimension / weight:
137 x 80 x 40 mm
RS485 Adapter RS232
NC = Not connected RS485 A = - RS232
RS485 B RS485 B = + RS232
RS485 A
G = Ground Transmission distance:
1000 meters/3281 feet
Page 8