Preparation For Electrical Connections; Product Maintenance - Comunello Automation EAGLE / ONE Instrucciones De Uso

• Insert the key into the cylinder (FIG. 16C) and turn it in the permitted
direction (FIG. 17C).
• Insert the release lever (FIG. 16C) and turn it in the permitted direction
(FIG. 17C).
• Keeping the lever rotated, move the gate in order to release the
mechanism (FIG. 17C).
To lock the gate leaf, proceed as follows:
MANUAL LOCKING WITH THE SUPPLIED KEY:
• Insert the key and turn it back to its original position (FIG. 18A).
• Move the gate to lock it automatically.
• Remove the key from the cylinder.
MANUAL LOCKING WITH THE SUPPLIED LEVER:
• Insert the lever and turn it back to its original position (FIG. 18B).
• Move the gate to lock it automatically.
MANUAL LOCKING WITH THE SUPPLIED LEVER:
• Insert the lever and turn it back to its original position (FIG. 18C).
• Insert the key and turn it back to its original position.
• Move the gate to lock it automatically.
• Remove the key from the cylinder.
5 PREPARATION FOR
ELECTRICAL CONNECTIONS
WARNING! To connect to the network, use a multipolar cable provided by
regulations by the book's unit.
1. Open the foundation box (FIG.15).
2. Connect the cable to the external circuit board by routing it through the
conduit positioned at the time of installation (FIG.19).
3. Connect the yellow/green wire (earth) to the terminal eye already present
alongside the cable inlet hole (FIG. 19) (for models of class I).
6 TESTING
Each part of the automation system, e.g. safety edges, photocells,emergency
stop, etc. must be tested; follow the procedures shown in the instruction
manuals supplied with the devices in question. Perform the following
sequence of operations for testing of EAGLE:
• Check that all the prescriptions in this manual have been followed
scrupulously, with special attention to the matters set down in chapter 1
"Prescriptions";
• Using the supplied control or stopping devices (key selector switch,
control buttons or radio transmitters), perform gate opening, closing and
stopping tests and make sure the gate responds correctly to the various
commands.
• Check operation of all the system's safety devices (photocells, safety
edges, emergency stop, etc.) one by one.
• If potentially hazardous situations caused by movement of the gate leaf
have been eliminated by limitation of impact force, the associated force
must be measured as prescribed in standard EN 12445.

7 PRODUCT MAINTENANCE

Maintenance must be carried out at regular intervals by qualified personnel
in compliance with the provisions of statutory legislation and the regulations
in force. EAGLE must be subjected to scheduled servicing at least once
every 6 months.
• Disconnect the operator from all power supplies.
• Check all the moving parts and replace any worn parts.
• Check all parts of the automation system for signs of deterioration.
• Grease with proper grease.
8 SPARE PARTS
Spare parts can be purchased by contacting the technical service.
9 DISPOSAL
At the end of its useful life the automation system must be dismantled by
qualified personnel and the materials must be recycled or disposed of in
compliance with the local legislation in force.
10 WARRANTY
fmndjklsvnbdsjkl Fratelli Comunello SpA provides a warranty for 24 months
for the correct functioning of the actuators from the date of manufacture,
provided that the performance specications indicated in the product
instruction manuals are respected. Free of charge repair and replacement
of components that are found to be faulty according to the indisputable
judgment of the company's technical staff shall be guaranteed at the
sole discretion of Fratelli Comunello Spa, and so excluding any claim for
damages made by others. Warranty material shall be returned to Fratelli
Comunello S.p.a. headquarters carriage paid and will then be shipped to
the customer carriage unpaid. The material found to be faulty and returned
to Fratelli Comunello S.p.a. shall remain property of the Seller. Any cost
resulting from any work needed to repair the defect or to replace the
material shall be charged to the Buyer. No compensation shall be allowed
for the period of device inactivity. Work under warranty does not prolong the
warranty period. The defect of the product shall be reported by the Buyer
within 8 (eight) days from its discovery or from the date of delivery of the
goods, under penalty of invalidation of the warranty. Such claim shall be
notied in writing.
Warranty does not cover:
Any product defect or damage that may have been incurred during
transport; any defect or damage arising from any fault and/or from neglect,
inadequacy and misuse of the electrical wiring in the Buyer's property; any
defect or damage caused by any repairs carried out by non authorised
personnel or by incorrect use/installation (with reference to this, system
maintenance is recommended every 6 months) or if not original spare parts
are used; any defect caused by chemicals or atmospheric conditions. The
warranty does not cover any cost neither for consumable materials nor for
alleged defects or convenient surveys.
Product Features Fratelli Comunello SpA products are subjected to
continue changes and improvements; their technical features and image
may therefore change without previous notice.
Competent court
Since the contract of sale is conrmed by an Order Conrmation drawn up
in Rosà, any such dispute shall be settled by the laws of Italy and by the
court of Vicenza (VI).
COMUNELLO ®Copyright 2017 - All rights reserved
15