Recalling A Preset Macro; Editing A Preset Macro; Programming; Programming A Program - Futurelight CP-256 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

6.4.2 Recalling a Preset Macro

Press the Manual-button and select the desired projectors via the respective projector select buttons.
Press the Macro-button and choose the desired projector select button (e.g. projector select button 1 - macro
green). All selected projectors show the chosen colour (e.g. green). Press the Macro-button in order to leave
the Macro-mode.

6.4.3 Editing a Preset Macro

Press the Manual-button and select the desired projector via the respective projector select button.
Press the Macro-button and choose the desired projector select button for editing the macro (e.g. projector
select button 1 - macro green). Adjust the desired colour (e.g. green) via channel fader 1. Press the Enter-
button in order to save the setting. Press the Macro-button in order to leave the Macro-mode.
Select the next projector via the respective projector select button. Press the Macro-button and choose the
same projector select button as for projector 1 (e.g. projector select button 1 - macro green). Adjust the
desired colour (e.g. green) via channel fader 1. Press the Enter-button in order to save the setting. Press the
Macro-button in order to leave the Macro-mode.

6.5 Programming

A program is a sequence of different scenes that will be called up one after another. With the CP-256, you
can program up to 16 different programs which can be assigned to the projector select buttons 1-16.

6.5.1 Programming a program

Press the Menu-button and select "Menu 2 Make Prog." via the Up/Down-buttons or the Data Entry fader.
Press the Enter-button twice. Select the desired program via the projector select buttons. Adjust the desired
settings via the joystick and the respective channel faders. Select the next projector via the projector select
buttons and adjust the settings. Press the Enter-button in order to save the first step. Program the next steps
until the program is finished or the maximum number of steps - 16 has been reached. Press the Escape-
button and the Enter-button in order to save the program.

6.5.2 Running a program

Press the Program-button and select the desired program via the projector select buttons. Adjust the
program speed via the Speed-Fader and the repitition rate via the Rate-Fader.

6.5.3 Checking a program

Press the Program-button and select the desired program via the projector select buttons. Press the Scene-
button and check every scene individually by pressing the respective projector select button.

6.5.4 Editing a program

Should you notice that a scene does not correspond to your imagination or when programs have to be edited
for a new stage, it is necessary to modify a scene manually.
First note the total number of steps. Press the Menu-button and and select "Menu 2 Make Prog." via the
Up/Down-buttons or the Data Entry fader. Press the Enter-button twice. Select the desired program via the
projector select buttons.
Select the desired scene via the Up/Down-buttons. If you hold the Recall-button and press the Up/Down-
button at the same time, the current scene is shown. Select the desired projector via the projector select
buttons. Adjust the desired settings via the joystick and the respective channel faders. Select the next
projector via the projector select buttons and adjust the settings. Press the Enter-button in order to save the
edited step. Edit the next steps until the program is finished.
Caution: Before leaving the Edit-Mode, the last step of the program has to be saved another time.
Otherwise, the program will not run correctly.
Select the last scene via the Up/Down-buttons. Press the Recall-button in order to show the memorized
scene. Save this scene by pressing the Enter-button. Press the Escape-button and the Enter-button in order
to save the edited program.
34

Publicidad

Tabla de contenido
loading

Tabla de contenido