Parts Description - Makita DVC860L Manual De Instrucciones

Indicating the remaining battery capacity
(Only for battery cartridges with "B" at the end of the
model number.) (Fig. 7)
Press the check button on the battery cartridge to indicate
the remaining battery capacity. The indicator lamps light
up for few seconds.
Indicator lamps
Lighted Off
015658
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Switch action (Fig. 8)
To start the cleaner:
1. Set the stand-by switch to the "I" side. The cleaner
gets into stand-by state.
2. Press the power button.
To make the cleaner get into stand-by mode, press the
power button again.
To turn off the cleaner, set the stand-by switch to the "O"
side.
The suction power can be adjusted according to your
work need.
Suction power can be increased by turning the suction
force adjusting knob from the
symbol.
NOTICE:
• Always set the stand-by switch to the "O" side when not
using the cleaner for long time. The cleaner consumes
power during stand-by state.
Auto-suction stop during wet suction
operation (for the cloth filter model)
WARNING:
• Do not use for a long time while the float is at work.
Using the cleaner with its float at work for a long time
can cause overheat, resulting in the cleaner
deformation.
• Do not pick up foam or soapy liquid. Picking up
foam or soapy liquid can cause foam to come out of air
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery may
have
malfunctioned.
symbol to the
exit before the float works. Continuing to using in this
condition may cause an electric shock and breakage of
the cleaner.
Auto-suction stop works only when using with the float
and float cage.
The cleaner has a float mechanism that prevents water
from immersing into the motor when picking up more than
a certain amount of water.
When the tank is full and the cleaner no longer picks up
water, switch off the cleaner and empty the tank.
Locking or unlocking the caster (Fig. 9)
To lock the caster with a stopper, lower the stopper lever
and the caster no longer will rotate. To release the caster
from the locked position, raise the stopper lever.
Locking the caster is convenient when storing the cleaner,
stopping the work on the way and keeping the cleaner
still.
To operate the stopper, move it by hand.
NOTE:
• When moving the cleaner, make sure that the caster is
unlocked. Moving the cleaner with the caster in the
locked position may cause damage to the caster.
Carriage handle (Fig. 10)
When carrying the cleaner, carry it by holding the handle
on the head. The handle is retractable at the head when
not in use.

PARTS DESCRIPTION

Model DVC860
(Cloth filter (for dry and wet dust) model) (Fig. 11)
Model DVC861
(Powder filter (for dry dust) model) (Fig. 12)
ASSEMBLY
CAUTION:
• Always be sure that the cleaner is switched off,
unplugged, and the battery cartridge is removed before
carrying out any work on the cleaner.
• Always wear dust mask during assembly or
maintenance.
Installing the powder filter and prefilter
(for dry dust) (optional accessory for
cloth filter model) (Fig. 13 & 14)
CAUTION:
• Never pick up water or other liquids or wet dusts when
using the powder filter. Picking up such things may
cause the powder filter breakage.
To use powder filter, remove the float cage and float by
removing the bolts.
Place the prefilter in the tank.
Next, mount the damper on the powder filter and then
place them in the prefilter.
When installing powder filter and prefilter, align the
mounting position marking on each of them with that one
at the top of the tank.
11