Publicidad
Idiomas disponibles
Idiomas disponibles
2,
When
the desired
thickness
is reached,
the ice sheet is
released
and slides onto
a cutter
grid.
The grid divides
the
sheet into individual
cubes.
3.
The water
containing
the rejected
minerals
is drained
after
each freezing
cycle.
4.
Fresh water
enters
the machine
for the next ice making
cycle.
5.
Cubes fall
into the storage
bin. When
the bin is full, the ice
maker
shuts off automatically
and restarts
when
more ice is
needed.
The ice bin is not refrigerated,
and some melting
will occur.
The amount
of melting
varies
with
room
temperature.
NOTE: As the room and water temperatures
vary, so will the
amount of ice produced and stored. This means that higher
operating
temperatures
result in reduced ice production.
{}@sf_o
s
Usng the
1.
To start
ice production,
press ON/OFF.
2.
To stop ice maker
operation,
press ON/OFF.
NOTES:
•
Pressing the On/Off
button does not shut off power to the
ice maker.
•
Allow 24 hours to produce the first batch of ice. Discard the
first 2 batches produced.
Acceler-lce
Mode
Select
the Acceler-lce
feature
when
you have an upcoming
need
for a large
amount
of ice and the ice bin is low or empty.
Acceler-lce
mode
will produce
a greater
quantity
of ice in a
24-hour
period.
•
Press ACCELER-ICE while the ice maker is on. The indicator
light will illuminate.
•
Press ACCELER-ICE again to turn off the Acceler-lce
feature.
The indicator
light will turn off.
•
The Acceler-lce
mode will be on when you first turn on the
product. It will turn off after 24 hours. To turn Acceler-lce
back on, press ACCELER-ICE.
Clean
It is recommended
that you clean
the ice maker
when
the
"Cleaning
Needed"
light is illuminated
or 9 months
has elapsed
or ice production
decreases
significantly.
To clean
your
ice
maker,
see "Ice Maker
System"
in the "Cleaning"
section.
Door Ajar Alarm
The Door Ajar
Alarm
feature
sounds
an alarm
when the ice
maker
door
is open
for 5 minutes.
The alarm
will repeat
every
2 minutes.
Close the door to turn off. The feature
then resets and
will reactivate
when the door
is left open
again
for 5 minutes.
Your new ice maker may make sounds that are not familiar to
you. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal.
Hard surfaces such as floors, walls and cabinets can make the
sounds seem louder than they actually
are. The following
describes the kinds of sounds that might be new to you and
what may be making them.
•
You will hear a buzzing sound when the water valve opens
to fill the water pan for each cycle.
•
Rattling noises may come from the flow of the refrigerant
or
the water line. Items stored on top of the ice maker can also
make noises.
•
The high-efficiency
compressor may make a pulsating or
high pitched sound.
•
Water
running over the evaporator
plate may make a
splashing sound.
•
Water
running from the evaporator
plate to the water pan
may make a splashing sound.
•
As each cycle ends, you may hear a gurgling
sound due to
the refrigerant
flowing in your ice maker.
•
You may hear air being forced over the condenser by the
condenser fan.
•
During
the harvest
cycle,
you may hear a "thud"
when
the
ice sheet slides from
the evaporator
onto
the cutter
grid.
•
When
you first start
the ice maker,
you may hear water
running
continuously.
The ice maker
is programmed
to run a
rinse cycle
before
it begins
to make
ice.
•
If the ice maker
is connected
to a water
supply
pressure
in
excess of 60 psi, you may
hear a loud
sound during
water
filling
associated
with the flow
of water
through
the inlet
valve.
Call a licensed,
qualified
plumber
to determine
the
best method
to reduce
the supply
water
pressure
(50 psi is
recommended).
15
Publicidad
