Additional Safety Rules For Long Reach Sanders - SPARKY SM717CE Instrucciones De Uso

b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety meas-
ures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for op-
erations different from those intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
IV - Additional safety
rules for long reach
sanders
Safety Warnings Common for Sanding:
а) This power tool is intended to function
as a sander. Read all safety warnings,
instructions, illustrations and specifica-
tions provided with this power tool. Fail-
ure to follow all instructions listed below may
result in electric shock, fire and/or serious
injury.
b) Operations such as grinding, wire brush-
Original instructions
ing, polishing or cutting-off are not rec-
ommended to be performed with this
power tool. Operations for which the power
tool was not designed may create a hazard
and cause personal injury.
с) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because
the accessory can be attached to your pow-
er tool, it does not assure safe operation.
d) The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can
break and fly apart.
е) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool. In-
correctly sized accessories cannot be ad-
equately guarded or controlled.
f) The arbour size of flanges, backing pads
or any other accessory must properly fit
the spindle of the power tool. Accesso-
ries with arbour holes that do not match the
mounting hardware of the power tool will
run out of balance, vibrate excessively and
may cause loss of control.
g) Do not use a damaged accessory. Be-
fore each use inspect the accessory
such as backing pad for cracks, tear
or excess wear, wire brush for loose or
cracked wires. If power tool or accessory
is dropped, inspect for damage or install
an undamaged accessory. After inspect-
ing and installing an accessory, posi-
tion yourself and bystanders away from
the plane of the rotating accessory and
run the power tool at maximum no-load
speed for one minute. Damaged acces-
sories will normally break apart during this
test time.
h) Wear personal protective equipment. De-
pending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of fil-
trating particles generated by your opera-
tion. Prolonged exposure to high intensity
noise may cause hearing loss.
i) Keep bystanders a safe distance away
from work area. Anyone entering the
5
EN