Cleaning And Care - WMF Kitchenminis Instrucciones De Uso

Cleaning and care

Cleaning
Remove the mains plug and allow the appliance to cool down. Do not
immerse the appliance in water, but rather clean it using a damp cloth
with a little washing-up liquid and then dry it. Do not use any harsh or
abrasive cleaning agents.
The heating bowl (5) is made of stainless steel. If rust spots do appear
however, they are only deposits that have formed on the surface. You
must remove these immediately using a stainless steel cleaning agent.
The egg insert (3) and cover with integrated water measuring device (1a)
are made of high-quality Tritan® and can be cleaned in the dishwasher.
Descaling
Limescale deposits lead to energy losses and have a negative effect
upon the appliance service as well as the cooking results. The appliance
switches off prematurely if the layer of limescale is too thick. The
limescale is then very difficult to remove. Therefore descale the appliance
regularly.
We recommend using Cromargol®. This product is highly effective, food
safe and is neutral in taste and smell. Thanks to its special care formula
with six high-quality and protective additives, Cromargol® is also very
gentle on materials.
You can usually purchase Cromargol® from the store where you have
purchased your appliance or from your chosen dealer. The Cromargol®
decalcifier is only available in Germany and Austria.
▪ Prior to descaling, unplug the appliance from the mains and allow it
to cool down.
▪ Pour half a portion (50 ml) of Cromargol® into the heating bowl
(5) and leave the appliance to stand until the layer of limescale has
detached from the base. Then fill the heating bowl (5) with cold tap
water to cover the limescale ring on the wall and leave to stand for
15 minutes.
▪ Then pour out and thoroughly rinse with cold tap water.
▪ Measure out and use other descaling agents according to the
manufacturer's instructions.
Do not heat the solution during descaling.
Caution: the warranty does not cover damage caused by not observing
the descaling instructions.
14
For UK use only
• This product is supplied with a 13 A plug conforming to BS 1363 fitted to
the mains lead. If the plug is unsuitable for your socket outlets or needs to be
replaced, please note the following. If the plug is a non-rewireable one, cut
it from the mains lead and immediately dispose of it. Never insert it into a
socket outlet as there is a very great risk of an electric shock.
• The replacement of the plug at the mains lead has to be done according to
the following instructions:
Warning - This appliance must be earthed!
Important: The wires in this mains lead are coloured in accordance with the
following code:
green/yellow Earth
blue Neutral
brown Live
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
⋅
the wire which is coloured green and yellow must be connected to
the terminal which is marked with the letter E or by the earth symbol
, or coloured green or green and yellow,
⋅
the wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black,
⋅
the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
• If a 13 A (BS 1363) plug is used it must be fitted with a 3 A fuse
conforming to BS 1362 and be ASTA approved. If any other type of plug
is used, the appliance must be protected by a 5 A fuse either in the plug
or adapter or at the distribution board. If in doubt - consult a qualified
electrician.
• Never use the plug without closing the fuse cover.
The appliance complies with the European directives 2014/35/EU, 2014/30/EU
and 2009/125/EU.
At the end of its lifetime this product must not be disposed of through the
normal domestic waste, but it should be handed to an assembly point for
the recycling of electrical and electronical appliances. You can inquire about
details at the local administration.
Subject to technical changes.
15