Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
tool (see technical data). The minimum conductor
size is 1.5 mm
.
2
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
)
2
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment
always unplug the tool.
Mounting and removing the guard (fig. B)
• Place the angle grinder on a table, spindle up.
• Release the clamping lock (6) and hold the
guard (4) over the tool as shown.
• Align the lugs (7) with the notches (8).
• Press the guard down and rotate it to the
required position.
• If required, increase the clamping force by
tightening the screw (9).
• Tighten the clamping lock.
• To remove the guard, release the clamping
lock.
Never use the tool without the guard in
place.
28
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
Fitting and removing a grinding or cutting disc
(fig. C1 & C2)
• Place the tool on a table, guard up.
• Fit the inner flange (10) correctly onto the
spindle (11) (fig. C1).
• Place the disc (12) on the flange (10). When
fitting a disc with a raised center, make sure that
the raised centre (13) is facing the flange (10).
• Screw the outer flange (14) onto the spindle
(11) (fig. C2):
- the ring on the flange (14) must face towards
the disc when fitting a grinding disc (A);
- the ring on the flange (14) must face away
from the disc when fitting a cutting disc (B).
60
• Press the spindle lock (3) and rotate the
spindle (11) until it locks in position.
6
10
• Tighten the flange (14) with the two-pin
15
spanner supplied.
20
• Release the spindle lock.
25
• To remove the disc, loosen the flange (14) with
-
the two-pin spanner.
-
-
6
6
6
6
15
Fitting a wire cup brush
15
• Screw the wire cup brush directly onto the
20
spindle without using the spacer and threaded
-
flange.
Mounting and removing the rubber backing
pad (fig. D)
The rubber backing pad is available as an option.
• Remove the guard from the tool.
• Press the backing pad (15) onto the spindle
(11). The inner flange is not needed.
• Position the abrasive disc (16) on the pad.
• Screw the outer flange (14) onto the spindle
(11).
• Press the spindle lock and rotate the pad (15)
until it locks in position.
• Tighten the flange (14) using the two-pin
spanner supplied.
• Release the spindle lock.
• To remove the pad, loosen the flange (14) with
the two-pin spanner.
Mounting the side handle (fig. E)
• Screw the side handle (5) tightly into one of the
holes (17) on either side of the gear case.
Do not use a damaged disc.
Publicidad
