Sawing With The Adaptation Table; Environment; Eu Declaration Of Conformity - Festool CARVEX PS 420 EBQ Manual De Instrucciones Original

C A R V E X
GB
Ensure that the angle table is firmly seated in the
guide.
Setting the angle

Turn the adjusting wheel [7-1] to select the re-
quired angle.
You can select the angles -45°, 0° and +45° on the
scale [7-2] .
WARNING
Sawing cutting depths
Risk of injury

Select the saw blade length and cutting depth so
that the saw blade remains plunged in the work-
piece.
 For 90° cuts, we recommend setting the angle
table to a small negative angle to guarantee
smooth operation.
10.4

Sawing with the adaptation table

The adaptation table ADT-PS 400 is used for attach-
ing your jigsaw to the Festool guide rail, the circle
cutter KS-PS 400 and the CMS modular system.
With guide rail and circle cutter: do not ex-
ceed max. material thickness of 20 mm and
always use cross-set saw blades (FSG).
Installing the adaptation table

Remove the saw table [1-11], (see chapter 7.4).

Mount the adaptation table [8-1] on the saw ta-
ble support.

Close the change lever [1-9].
Ensure that the adaptation table is firmly seated in
the guide.
 Use the extractor connector [1-8] also with the
adaptation table.
Adaptation to the guide rail FS 2
The Festool guide system FS 2 (Fig. [9]) makes it
much easier to manufacture straight precision cuts.

Place the jigsaw with attached adaptation table
[8-1] on the guide rail.
Adaptation to the circle cutter
The circle cutter can be used to create circular cuts
with a diameter between 120 and 3000 mm. The cir-
cle cutter can be installed from both sides on the
adaptation table.

Place the jigsaw with attached adaptation table
on the adapter [10-1] on the circle cutter.

Insert the centring mandrel [10-2] in the hole
[10-4] on the circle cutter aligned with the saw
blade.
18

Clamp the measuring tape to the circle cutter
using the rotary knob [10-5].
Recommended when using the circle cutter:

Cut in an anticlockwise direction.

Work at a slow rate of advance.

Set the pendulum stroke [1-12] to 0 - 1.

Set the stroke rate [1-5] to 1 - 5.
 Store the centring mandrel in the depot [10-3].
Semi-stationary sawing with the Festool CMS system
When combined with the Festool CMS system, the jig-
saw becomes a semi-stationary bench saw for profiled
cuts. See the CMS brochure for more information.

Install your jigsaw with adaptation table in the
CMS as described in the operating manual for
the CMS-PS.
11

Environment

Do not dispose of the device in house-
hold waste! Recycle devices, accesso-
ries and packaging. Observe applica-
ble country-specific regulations.
EU only: European Directive 2002/96/
EC stipulates that used electric power tools must
be collected separately and disposed of at an envi-
ronmentally responsible recycling centre.
Information on REACh:www.festool.com/reach
12

EU Declaration of Conformity

Jigsaw
PSB 420 EBQ 10003822, 10004924, 10003822
PS 420 EBQ 10003702, 10004876, 10003702
Year of CE mark: 2012
We declare under sole responsibility that this prod-
uct complies with the following directives and stan-
dards:
2006/42/EG, 2004/108/EG, 2011/65/EU, EN 60745-
1, EN 60745-2-11, EN 55014-1, EN 55014-2, EN
61000-3-2, EN 61000-3-3.
Festool Group GmbH & Co. KG
Wertstr. 20, D-73240 Wendlingen, Germany
Dr. Martin Zimmer
Head of Research, Development and Technical
Documentation
31.01.2013
Serial no.