Würth master HKS 52 Instrucciones De Servicio página 22

d) Always ensure that the lower guard is cover-
ing the blade before placing saw down on
the workbench or the fl oor. An unprotected,
coasting blade will cause the saw to walk back-
wards, cutting whatever is in its path. Always
keep in mind the time it takes for the blade to
fi nally stop after the trigger switch is released.
Additional safety instructions for all
saws with a riving knife
a) Use the appropriate riving knife for the blade
being used. For the riving knife to work it must
be thicker than the body of the blade, but thinner
than the blade's teeth.
b) Adjust the riving knife as described in this
instruction manual. Incorrect spacing, posi-
tioning and alignment can make the riving knife
ineffective in preventing kickback.
c) The riving knife must be engaged in the
workpiece for it to work. The riving knife is
ineffective in preventing kickback in a short cut!
d) Never use the saw if the riving knife is bent.
Even a minor problem can slow the closing rate
of a guard.
Additional safety warnings for
circular saws
❏ Always wear ear protectors! Exposure to
noise can cause hearing loss.
❏ Always wear a dust mask! Inhaling dust parti-
cles can cause breathing diffi culty and possible
injuries.
❏ Never use saw blades with larger or smaller
diameters than recommended. Refer to the
technical specifi cations to fi nd the correct cut-
ting capacity rating. Use only the saw blades
specified in this manual that comply with
EN 847-1.
❏ Never use abrasive circular saws.
❏ Ensure that the riving knife is adjusted so that
the gap between the riving knife and the rim of
the blade is not more than 5 mm and that the rim
of the blade does not extend more than 5 mm
beyond the lowest edge of the gap.
Residual risks
The following risks are inherent to the use of circular
hand saws.
– Injuries will be caused by touching the rotating
parts or hot parts of the tool.
Certain residual risks cannot be avoided despite
abiding by the relevant safety regulations and using
safety devices. These are:
22-English
– Impairment of hearing.
– Risk of crushing your fi ngers when changing an
accessory.
– Health hazards caused by inhaling dust gener-
ated when working with wood.
Use original Würth accessories only.
Technical specifi cations
Article-No.
Mains voltage
Power consumption
No-load speed min
Cutting depth
- 90 (without guide rails) mm
- 90 (with guide rails) mm
- 45 (without guide rails) mm
- 45 (with guide rails) mm
Diameter, saw blade mm
Thickness, blade disc mm
Locating holes, saw blade mm
Bevelled angle adjustment
Weight
Protection category
Fuses:
230V power tool 10 A power supply
Unit components
1. Operating switch
2. Switched on locking button
3. Front handle
4. Saw blade lock
5. Dust extraction outlet
6. Shoe
7. Riving knife
8. Saw blade guard retraction handle
9. Saw blade guard
10. Saw blade
11. Bevel adjusting lever
12. Fence adjustment screw (HKS 62)
13. Rail adjuster: Cutting
14. Rail adjuster: Bevelling
15. Bevel adjustment markings
16. Straight cut mark
17. Depth adjustment knob
18. Parallel fence
19. Saw blade clamping screw (*)
20. Washer (*)
21. Washer (*)
22. Screws (*)
HKS 52 HKS 62
0702 153 X 0702 154 X
V 230 230
W 1 050 1 350
-1
5 000 5 000
52 62
47 57
37 49
32 44
165 190
2.5 2.6
20 30
0 - 45° 0 - 55°
kg 5.0 6.0
II II