Initial Use - Topcom BABYVIEWER KS-4248 Manual De Usuario

®
Thanks this digital technology, this equipment is protected against
eavesdropping and immune to interference from other equipment.
The baby unit starts transmitting as soon as the microphone picks
up a sound. The sound is reproduced by the parent unit. The
microphone sensitivity can be adjusted by the user (see "10.12
Voice activated transmission (VOX)").
The babyphone can never replace proper
supervision by an adult; it only provides support.
7.1 Baby unit components
See Figure on the fold-out page.
A
1 On/off LED
2 Night light LED
3 Infrared LED for night
vision
4 On/off switch
5 Lens
6 Microphone
7 Wall mounting cavity
7.2 Parent unit components
See Figure on the fold-out page.
B
13 Volume LED
14 Microphone
15 Increase volume /
Up
16 Decrease volume /
Down
17 Decrease brightness /
previous menu item
7.3 Display description
Out of range or no
connection
Volume icon
Melody icon
8

Initial use

8.1 Package content
The equipment is supplied as standard with the following items:
- 1 baby unit
- 1 parent unit
- 2 AC mains adapters
8.2 Installing batteries in the baby unit (KS-4248)
• You can operate the baby unit with 4 AAA
cells (LR03; we recommend alkaline cells)
or the included AC mains adapter.
• The baby unit cannot recharge batteries.
• It is recommended to always leave the
batteries in the unit, even if you use the AC
mains adapter. The unit will automatically
switch to battery power in case of a mains
power interruption.
– Turn the screw on the cover of
the battery compartment at
the back of the baby unit 90°
counter clockwise and remove
the battery compartment
cover.
4
8 Light sensor
9 Pair button
10 Speaker
11 Connector for AC mains
adapter
12 Room temperature sensor
21 Power on/off LED
22 Menu button
23 Push to Talk button
24 On/off button
25 Stand
26 Speaker
27 Connector for AC mains
adapter
28 Battery cover with screw
- 1 user guide
- 1 Li-ion rechargeable battery pack
OPEN
90° MAX
Babytalker 3500 SEDS
Do not turn the screw past the "OPEN" point.
– Fit four AAA alkaline
cells (LR03) in the
battery compartment.
Ensure that the polarity is
correct.
– Close the battery
compartment.
Never mix used cells with fresh cells.
8.3 Connecting the baby unit to the AC mains
Insert the small plug of the
AC mains adapter in the
mains power connector of
11
the baby unit and plug
the AC mains adapter into a
mains connector (100~240
V - 50/60 Hz).
CAUTION
• The mains connector must be within easy reach so
you can quickly unplug the power cable in an
emergency.
• Use only the supplied AC mains adapter (5.9V
DC / 800 mA).
8.4 Installing the rechargeable battery pack in
the parent unit
See Figure on the fold-out page.
B
CAUTION
• Use only the supplied Li-ion battery pack in the parent
unit.
– Rotate the stand
28
– Turn the screw on the cover of the battery compartment
at the back of the parent un and remove the battery
compartment cover.
– Place the Li-ion battery pack in the battery compartment.
Ensure that the battery contacts do make contact with
the charge contacts as illustrated.
– Carefully close the battery compartment and rotate the
belt clip back downwards.
8.5 Connecting the parent unit to the AC mains
– Insert the small plug of the AC mains adapter in the
mains power connector
adapter into a mains connector (100~240 V - 50/60 Hz).
It takes around 10 hours to fully charge the
batteries.
9 Installing the Babyviewer
9.1 Fine tuning
• Place the camera in a convenient location, point the lens of
the camera to the observation area.
• Adjust the angle by rotating the camera.
upward.
and plug the AC mains
27