albatros IdroTwo Manual De Uso página 11

Operating Instructions
When the disinfection cycle ends, the keyboard
returns to standy-by mode, and all the LEDs
except LED 1 and LED 2 switch off (see
below).
If the disinfection cycle does not start, check
that other functions have not been selected and
that the disinfectant tank contains disinfectant
(without which the disinfection cycle cannot be
started); if not, fi ll the tank and repeat the start-
up procedure.
IDROTWO
ON/OFF KEY
AIRPOOL
This key switches the AIRPOOL hydromassage
function on and off.
Press the key once: the AIRPOOL function
begins, and the top left-hand corner of the
keyboard lights green to show that the function
has been started.
To switch off the AIRPOOL function, simply press
the same button again.
Level of water in the tub (LED 1):
When the level of water is not suffi cient for
Led 1
operation of the hydromassage system, the light
is RED. When the level necessary for operation
of the system is reached, this light turns GREEN
and remains GREEN for the entire hydromassage
cycle.
Level of disinfectant in the tank (LED 2):
Led 2
This LED lights RED when the disinfectant tank
is empty, and GREEN when the tank is full.
5 Operation:
When the tub is switched on, only the two
level indicator LEDs (L1 and L2) will be lit. The
WHIRLPOOL and AIRPOOL (only for IDROTWO)
hydromassage systems can be operated either
independently or simultaneously.
Here is an example of how to operate the
system.
First, fi ll the tub with lukewarm water:
If you wish to select the WHIRLPOOL and LYMPH
DRAINAGE functions together, fi rst press the
WHIRLPOOL button, followed by the LYMPH
DRAINAGE button, which starts the drainage
function.
Timer
20'
The hydromassage tub is fi tted with a timer
which automatically interrupts operation of the
hydromassage system after 20 minutes.
version only:
Filling the disinfectant reservoir
6
To fi ll the disinfectant reservoir, remove the fi ller
cap located on the edge of the tub
the keyboard) and introduce 1 litre of
(pilot light L2 on the keyboard will change from
red to green).
Led 2
A level sensor inside the reservoir checks for the
presence of disinfectant; if the reservoir is empty,
the disinfection cycle will not start.
The recommended disinfectant solution, which
is available through our authorized dealers and
Service Centres, not only sanitizes the appliance,
but also prevents fermentation and unpleasant
odours, and inhibits the formation of algae and
mildew.
IMPORTANT!
Do not use products containing chlorine
(Amuchina, Bleach etc.) as these may
damage the system and cause leakage of
disinfectant.
7 Disinfection cycle
The tubs feature the System Clean disinfection
system.
The disinfection cycle is an essential function
which guarantees the maximum hygiene and
correct operation of the appliance, since it
disinfects those parts of the system that cannot
be reached during normal cleaning.
With the System Clean disinfection system, the
water used for the hydromassage can be used.
The cycle can only be started when the tub is
fi lled with water.
Important:
Before starting the disinfection cycle ensure that
the tub is not in use.
Also ensure that all the hydromassage nozzles
are open.
The disinfection cycle lasts for about two minutes
and, once started, cannot be interrupted.
Starting the disinfection cycle
Before starting the disinfection cycle, ensure
that:
1) The main power switch is set to "ON".
Led 1
2) The level of water in the tub must be 5 cm
Manuale Uso VS ACEW / ACET - Code 10011523 - Edition 1 - 11/2007
11
disinfectant
above the hydromassage nozzles (pilot light
L1 on the keyboard lights GREEN).
English
(alongside