General Power Tool Safety Warnings - Makita GA7020R Manual De Instrucciones

ENGLISH (Original Instructions)
1. Shaft lock
2. Motor housing
3. Lock button
4. Handle
5. Lock lever
6. Switch trigger
7. Indication lamp
8. Wheel guard
9. Screw
10. Bearing box
SPECIFICATIONS
Model
Depressed center wheel diameter
Spindle thread
No load speed (n ) / Rated speed (n)
0
Overall length
Net weight
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Explanation of general view
11. Nut
12. Lever
13. Lock nut
14. Depressed center wheel
15. Super flange
16. Inner flange
17. Lock nut wrench
18. Outer flange 78
19. Cut-off wheel
20. Inner flange 78
GA7020R GA7030R
180 mm
8,500 (min
473 mm 503 mm
5.6 kg 6.3 kg
ENE048-1
2. Operations such as polishing are not
ENF002-1
3. Do not use accessories which are not specifically
4. The rated speed of the accessory must be at least
GEA010-1
5. The outside diameter and the thickness of your
6. The arbour size of wheels, flanges, backing pads
GEB033-3
7. Do not use a damaged accessory. Before each use
21. Dust collecting wheel guard
22. Exhaust vent
23. Inhalation vent
24. Commutator
25. Insulating tip
26. Carbon brush
27. Brush holder cap
28. Screwdriver
GA7040R GA9020R
M14
-1
)
473 mm
6.6 kg 5.8 kg
/II
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
GA9030R GA9040R
230 mm
-1
6,600 (min )
503 mm
6.5 kg 6.9 kg
5