Publicidad
C-Series Power Supply Instruction Manual
Technical Data
CS5.241
DC Output Voltage
24-28V
1)
Factory Set
typ.
24.1V
Output Current
nom. 5-4.3A
min.
6-5.1A
Output Power
nom. 120W
min.
144W
2)
Output Ripple
max. 50mVpp
AC Input Voltage
-
100-120Vac/
200-240Vac
±10%
Auto-Select
3)
AC Input Current
max. 2,6 / 1,3A
DC Input
-
--
4)
Power Factor
typ.
0,56 / 0,47
7)
Harmonic Correction
no
8)
EN 61000-3-2
not fulfilled
5)
Inrush Current
typ.
3A; 1A
typ.
3A; 1A
4)
Efficiency
typ.
89,4/90,2%
4)
Losses
typ.
14,5/13,2W
4)
Hold-up Time
typ.
80 / 78ms
6)
Dimensions
32x124x117
Limited Warranty
-
3 year
1) At full load
2) 50Ohm measurement, bandwidth 20MHz
5) Peak value and inrush energy at an ambient temperature of 40°C and cold start.
in order to reduce the amount of harmonic current. A not corrected unit does not necessarily mean that the EN 61000-3-2 is not fulfiled.
which is mandatory for some applications. See the special chapter below, whether this standard is required or not.
45°C. Above that temperature, do not use the short term power longer than a duty cycle of 10% and not longer than 1 minute every 10 minutes.
when continuously loaded with more than 120W and operated with a mains voltage of 100V or below.
EN 61000-3-2 Harmonic Standard (PFC)
When does a power supply have to comply with EN 61000-3-2 ?
(Standard for harmonic Input current)
1) When the end-device is used within the European Union and
2) When the end-device is connected to a public mains supply with a nominal voltage
≥ 220Vac and
3) When the power supply is:
- fitted in an end-device with an average input power in excess of 75W or
- fitted in an end-device with a continuous input power in excess of 75W or
- part of a lighting system.
Functional Diagram
L
Input
Input Fuse
Rectifier
N
&
&
Input Filter
Inrush
Limiter
115/230V
Auto-Select
only for
CS5.241
CS10.241
CS10.242
CS10.481
Overload Performance
Output Voltage
28V
24
20
16
12
8
4
Output Current
0
0
2
4
6
CS5.241, CS5.243, CS5.244
Parallel Use
The power supplies shall not be used in parallel in order to increase the output power.
However, units can be paralleled:
- for building 1+1 redundancy systems or
- to deliver short-term peak currents to the load when the average current is smaller than the current of one power supply
Inductive and Capacitive Loads
The unit is designed to supply any kind of loads, including unlimited capacitive and inductive loads.
CS5.243
CS5.244
24-28V
24-28V
24.1V
24.1V
5-4.3A
5-4.3A
9) 10)
9) 10)
9)
6-5.1A
6-5.1A
120W
120W
9) 10)
9) 10)
9)
144W
144W
50mVpp
50mVpp
100-120Vac
200-240Vac
±10%
±10%
--
--
2,6A / --
-- / 1,3A
--
210-375Vdc
0,59 / --
-- / 0,5
no
no
N/A
fulfilled
2
2
s
45A; 1A
s
--
2
2
s
--
30A; 1A
s
87,5% / --
-- / 89,5%
17,1W / --
-- / 14,1W
80ms / --
-- / 78ms
32x124x117
32x124x117
3 year
3 year
Output
Voltage
Regulator
Power
Output
Converter
Filter
Output
Over-
Voltage
Protection
Output Voltage
Adjust ment
Range
8
10
12A
CS10.241
CS10.242
CS10.243
24-28V
24-28V
24-28V
24.1V
24.1V
24.1V
10-8.6A
10-8.6A
10-8.6A
9)
12-10.3A
12-10.3A
12-10.3A
240W
240W
240W
9)
288W
288W
288W
50mVpp
50mVpp
50mVpp
100-120Vac/
100-120Vac/
100-120Vac
200-240Vac
200-240Vac
±10%
±10%
±10%
Auto-Select
Auto-Select
--
5,0 / 2,5A
5,0 / 2,5A
5,0A / --
--
--
--
0,59 / 0,51
0,59 / 0,57
0,57 / --
no
PFC Inductor
no
not fulfilled
fulfilled
N/A
2
2
3A; 1A
s
3A; 1A
s
85A; 8,5A
2
2
3A; 1A
s
3A; 1A
s
--
91,0/91,6%
90,8% / --
91,0/91,6%
24,1/22,4W
24,1/24,1W
24,0W / --
46 / 47ms
46 / 42ms
46ms / --
60x124x117
60x124x117
60x124x117
3 year
3 year
3 year
3) At full load and the lower end of the input voltage tolerance
6) Without DIN-rail
Exceptions:
End-devices for professional applications with an input power greater than 1000W do not need
to fulfill EN 61000-3-2.
Comments:
- The average input power must be determined in accordance with EN 61000-3-2.
- Industrial mains supplies with their own transformer are considered to be "non-public".
- Where individual self-contained items of equipment are installed in a rack or case
(e.g. devices connected in parallel), they are regarded as being individually connected to the
mains supply. The rack or case need not be tested as a whole. Alternatively it is also permitted
to assess the whole rack or case. This is recommended for devices used in professional
applications with an input power greater than 1000W.
Dielectric Strength
Input
L
V
OUT
N
+
+
A
-
Earth, PE
-
DC
ok
Adjustment
Range
28V
24
20
+60°C
16
+25°C
12
-25°C
8
4
Output Current
0
0
2
4
6
8
10
12
14
16
18
CS10.241, CS10.242, CS10.243, CS10.244
CS10.244
CS10.481
24-28V
48-52V
24.1V
48.0V
10-8.6A
5-4.6A
9)
9)
9)
12-10.3A
6-5.5A
240W
240W
9)
9)
9)
288W
288W
50mVpp
100mVpp
200-240Vac
100-120Vac/
±10%
200-240Vac
±10%
--
Auto-Select
-- / 2,5A
5,0 / 2,5A
210-375Vdc
--
-- / 0,52
0,59 / 0,51
no
no
not fulfilled
not fulfilled
2
2
s
--
3A; 1A
s
2
2
48A; 3A
s
3A; 1A
s
-- / 91,6%
91,4/92,0%
-- / 22,7W
22,6/20,9W
-- / 45ms
46 / 47ms
60x124x117
60x124x117
3 year
3 year
4) At full load and nominal input voltage
7) Harmonic correction describes whether the input current waveform is filtered
8) EN 61000-3-2 is the European PFC standard,
9) The short-term power / current is continuously allowed up to an ambient of
10) The unit can respond with a thermal shut-down
Type tests and factory tests:
Conducted by the manufacturer.
Do not repeat test in field!
Field test rules:
Output
(1) Use appropriate test equipment which
apply the voltage with a slow ramp!
+
(2) Connect L and N together as well as all
-
output poles.
(3) Use only AC test-voltages with 50/60Hz.
The output voltage is floating and has no ohmic
reference to ground.
A
Type Test
60s
2500Vac
Factory Test
5s
2500Vac
Field Test
5s
2000Vac
Output Voltage
60V
52V
50
48V
40
30
20
10
0
20A
0
1
2
ext. adjustable
at full load
continuous
short term
continuous
short term
DC to 20MHz
TN,TT,IT mains
120 / 230Vac
120 / 230Vac
120Vac
230Vac
120 / 230Vac
120 / 230Vac
120 / 230Vac
wxhxd (mm)
B
C
3000Vac
500Vac
2500Vac
500Vac
2000Vac
500Vac
Adjustment
Range
+60°C
+25°C
-25°C
Output Current
3
4
5
6
7
8
9
10A
CS10.481
Publicidad
