Programmable Parameters - LEGRAND LMTS-101-CCT Guia De Inicio Rapido

SETTING THE TIME AND DATE AND MODIFYING PROGRAMMING PARAMETERS
When the LMTS-101-CCT is powered up, it will first display a boot up screen showing the version
of the firmware in the unit and will then switch to the Home screen, as shown in the diagram to the
right. However, if the date and time have not yet been set, a message will display stating that the
date and time need to be set. To enter Setup mode, press the Select button. The Setup screen
displays. Press Select again to display the Set Time and Date screen. (See the following section
for detail on all programming parameters.
Navigating and Editing Parameters
When on the Setup screen, use the Up and Down buttons to select the specific function, then
press Select to display that screen. For all other screens:
With the Parameter
SET TIME AND DATE
highlighted, press
the Select button to
TIME:
toggle to the Value,
DATE:
OR press the Up
or Down buttons to
START:
move to a different
parameter.
PREVIOUS MENU
Setting Date/Time, Location, and Preferences
Home Screen
This screen displays the current date
and time, as well as if Daylight Savings
Time (DST is currently in effect). The
AM/PM designation does not display if
the unit is set to show a 24 hour clock
(see Preferences.)
The Prog line shows the number of
scheduling events. The one currently in
effect will blink.
Setup Screen
Press the Select button on the Home
screen to display this screen.
Use the Up and Down buttons to
choose an option and press Select.
To return to the Home screen, select
Main Page
Set Time and Date
Enter the current Time and Date.
These are used by Schedules to
determine when an event is active.
If following Daylight Savings Time, set
DST to "Enable". When enabled, the
Start and End parameters determine
when Daylight Savings Time begins
and ends.
Location
Enter the Longitude and Latitude
of the current location. A number of
latitude and longitude lookup tools exist
on the Internet. One example is www.
latlong.net. The Time Zone is calculated
automatically based on latitude and
longitude, but can be changed if needed.
The current Sunrise and Sunset times
are displayed, based on the location
and date settings.
SET TIME AND DATE
06 : 30 AM
08/14/16
DST: DISABLE
2nd Sun Mar
END: 1st Sun Nov

PROGRAMMABLE PARAMETERS

Mon 08/14/2016
12:46
Prog 1 2 3 4 5 6
SETUP
SET TIME AND DATE
LOCATION
PREFERENCES
SCHEDULING
MAIN PAGE
SET TIME AND DATE
TIME: 06 : 30 AM
DATE: 08/14/16
DST: DISABLE
START: 2nd Sun Mar
END: 1st Sun Nov
PREVIOUS MENU
LOCATION
LONGITUDE:
LONGITUDE:
TIME ZONE:
<Sunrise:
<Sunset:
PREVIOUS MENU
With the Value
highlighted, press
the Up or Down
TIME: 06 : 30 AM
buttons to change
DATE: 08/14/16
the value, OR press
DST: DISABLE
the Select button to
START: 2nd Sun Mar
toggle back to the
END: 1st Sun Nov
Parameter.
PREVIOUS MENU
Preferences
DST
The Time Format can be set to a
12 hour or 24 hour format. The Date
10
Format can be set to MM/DD/YY or
DD-MM-YY.
PM
The Display Intensity can be set to
a range of 10-100%. The Display
Timeout determines whether the display
will shut off after a period of time during
which no button on the LMTS-100-CCT
has been pressed. Available values:
10s (seconds), 20s, 30s, 40s, 50s, 1m
(minutes), 5m, 10m, or Never.
Select More Options to move to the
next preferences screen
Preferences (2)
The Button Lockout parameter will
disable the ON/OFF button on the
LMTS-100-CCT if set to "ON". The
Button Function parameter can be set
to the following values:
• Toggle Load – Turns all bound
loads in the DLM network ON or
OFF.
• Override Sch (Schedule) – Will
override all schedule events for
a period of time based on the
Override Duration parameter
(on the next Preferences screen).
Once the button is pressed, the
override can't be turned off until
the duration is ended.
-086°
• Override/Resume – Similar to
+33°
Override Sch, but in this case,
-06
pressing the button a second time
05:39>
will turn off the override.
19:02>
Select Next Menu to move to the next
Preferences screen.
Select Main Page to return to the
Setup screen.
3
DST
Mon 08/14/2016
12:46
10
PM
Prog 1 2 3 4 5 6
UP
DOWN
PREFERENCES
TIME FMT:
DATE FMT: MM/DD/YY
DIS INTENSITY:
DIS TIMEOUT:
MORE OPTIONS
PREFERENCES
Btn LOCKOUT:
Btn FUNCTION:
TOGGLE LOAD
NEXT MENU
MAIN PAGE
SELECT
CONFIG
ON/OFF
12 HOURS
90%
NEVER
OFF