Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Preferences (3)
The Override Duration parameter
determines how long a schedule event
is overridden, after the On/Off button is
pressed (when the Button Function
is set to Override Sch or Override/
Resume). Available values: 1,2, 3, or
4 hours, All Day (ends when Event 1
occurs the next day), or Next Sched
(ends when the next event occurs)
Select Main Page to return to the
Setup screen.
Creating or Modifying Schedule Events
The LMTS-100-CCT stores only one
schedule in memory at a time. A
schedule consists of 6 events for an
Astro schedule or 2-8 events for a
Custom schedule.
When the Scheduling screen is
selected from Setup, there are two
options. New Event List will delete the
current schedule and start new schedule
from default values. Edit Current Event
List will display current events and allow
you to modify those values.
Scheduling Event(s) Type
If you select New Event List on
the Scheduling screen, this screen
appears. Select either Astro or
Custom for the event type.
Custom Event Scheduling
Custom Schedules start with a default
of 5 events. You can add up to 3 more
for a total of 8. For each event you
select the Target CCT level, and then
select specific times for the Start and
Finish of that event. As with Astro
scheduling, the finish time of one event
can't overlap with the start time of the
next event. However, a gap of time can
occur between the end of one even
and the start of the next event.
When the Start time occurs, the CCT
value of the load will begin gradually
changing from the Target CCT value of
the previous event to the value of the
current event. It will reach the new value
at the Finish time. Therefore, the longer
the amount of time between start and
finish, the more gradual the change. If
there is a gap of time between the finish
of one event and the start of the next
event, the CCT level will remain the
same during that period of time.
All events must occur in a time frame
between 12:00 AM and 11:59 PM.
However, you do not have to start
event 1 at 12:00AM and end the last
event at 11:59 PM. There can be a gap
of time between the end of one day
and the start of the next.
PREFERENCES
OVERRIDE DURATION:
1 HOUR
MAIN PAGE
SCHEDULING
NEW EVENT LIST
EDIT CURRENT EVENT
LIST
SCHEDULING
EVENT(S) TYPE
ASTRO
CUSTOM
SCHEDULING
EVENT:
#1
TARGET CCT:
2000K
START:
12:00 AM
FINISH:
06:00 AM
NEXT
SCHEDULING
EVENT:
#2
TARGET CCT:
5500K
START:
06:00 AM
FINISH:
09:00 PM
PREV NEXT
SCHEDULING
EVENT:
#5
TARGET CCT:
2000K
START:
07:00 PM
FINISH:
11:59 PM
PREV DONE
Event 5 screen initial
default
After editing Event 1, select Next to
display Event 2. Continue editing events,
until you reach event 5. At this point, Next
is replaced by Done.
If you edit the Finish time so that it
occurs before 11:59 PM, the Add option
appears, allowing you to add another
event. The Start and Finish times
of the new event are set to the same
time as the Finish time of the previous
event. You can keep adding events, up
to 8 total, as long as the Finish time is
set to a value less than 11:59PM
Default Schedule Settings
By default, out of the box and after a reset, the LMTS-101 is set
to use Custom Event Schedule, with five events, set as follows:
Target CCT
Start
2000K
12:00 AM
5500K
6:00 AM
5500K
9:00 AM
2000K
5:00 PM
2000K
7:00 PM
Astro Event Scheduling
Astro Schedules have 6 predefined
events. For each event, set the Target
CCT level. The level is a percentage
of CCT defined by the min/max range.
By default, the six Events progress
through the following values from
sunrise through Nightime: 35%, 65%,
100%, 65%, 35%, 10%
The six events are pre-programmed to
specific general categories of the day for
the Start and Finish of the event. These
categories can't be changed. However,
for the Events that occur around Sunrise
or Sunset, you can modify the number
of minutes plus or minus the sunrise/
sunset time for that event to begin or
end. The range and default event values
are shown in the chart on the following
page.
As with Custom scheduling, the Target
CCT value will gradually change from
the value of the previous event to the
value of the current event, based on
the Start and Finish values.Events
cannot overlap. You can, however,
have a gap in time, as in the default
values of Events 5 and 6. If there is a
gap of time between the finish of one
event and the start of the next event, the
CCT level will remain the same during
that period of time.
4
SCHEDULING
EVENT:
TARGET CCT:
2000K
START:
07:00 PM
FINISH:
11:00 PM
PREV ADD DONE
Event 5 screen after
changing Finish time so
it ends before 11:59 PM
Finish
6:00 AM
9:00 AM
5:00 PM
7:00 PM
11:59 PM
SCHEDULING
EVENT:
(ASTRO) #1
TARGET CCT:
35%
START:
Sunrise+00
FINISH:
Sunrise+30
NEXT
Select Next to
display Event 2
SCHEDULING
EVENT:
(ASTRO) #2
TARGET CCT:
65%
START:
Sunrise+30
FINISH:
MORNING
PREV NEXT
... and so on through
events 3, 4, 5, and 6.
SCHEDULING
EVENT:
(ASTRO) #6
TARGET CCT:
10%
START:
Sunset+45
FINISH:
Sunset+75
PREV DONE
Select Done to return
to the Setup screen.
#5
Publicidad
Tabla de contenido
