Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GCM 10 S Professional Manual Original

OBJ_BUCH-1126-005.book Page 31 Wednesday, April 27, 2016 3:07 PM
Aligning the Fence
– Bring the machine into the transport position.
– Turn the saw table 17 to the 0° detent 16. The lever 14
must be felt to engage in the detent.
Checking: (see figure T1)
– Adjust an angle gauge to 90° and position it between the
fence 9 and the saw blade 7 on the saw table 17.
The leg of the angle gauge must be flush with the fence over
the complete length.
Adjusting: (see figure T2)
– Loosen all hex socket screws 28 with the hex key 30 pro-
vided.
– Turn the fence 9 until the angle gauge is flush over the com-
plete length.
– Retighten the screws again.
Aligning the Angle Indicator (Horizontally) (see figure U)
– Bring the machine into the transport position.
– Turn the saw table 17 to the 0° detent 16. The lever 14
must be felt to engage in the detent.
Checking:
The angle indicator 15 must be in alignment with the 0° mark
of the scale 10.
Adjusting:
– Loosen the fastening screw of the angle indicator with the
supplied cross-head screwdriver 30 and align the angle
indicator alongside the 0° mark.
– Retighten the screw again.
Transport
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 26 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– For lifting or transporting, hold the power tool by the re-
cessed grips 36 on the side of the saw table 17.
 The power tool should always be carried by two per-
sons in order to avoid back injuries.
 When transporting the power tool, use only the trans-
port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Bosch Power Tools
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Accessories
Material clamp
Insert plates
Dust bag
Angle adapter for dust bag
Extension bars
Saw blades for wood and plate materials, panels and
strips/mouldings
Saw blade 254 x 30 mm, 60 teeth

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always
include the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
English | 31
Article number
2 610 009 615
2 607 960 019
2 605 411 204
2 600 499 071
2 607 001 911
2 608 640 438
1 609 92A 2N6 | (27.4.16)