Before Use; Safety Instructions; Overhead Rigging - JB Systems Light TUBELED OUTDOOR Manual De Instrucciones

ENGLISH
INSTALLATION MANUAL
®
Thank you for buying this JB Systems product. To take full advantage of all possibilities, please read
these operating instructions very carefully.
The JB Systems TUBELED™ system contains the following components:
 The 1m long TUBELED™ tubes: to be connected to the controller.
 The TUBELED™ controller: controls the connected led tubes.
 Signal extension cables: 5m or 10m.
 Power extension cables: 5m, 10m or 20m.
This manual only explains installation of the tubes, refer to the controller user manual to know
everything about how to use the TUBELED™ system.
FEATURES
 Each TUBELED™ uses 144 high efficiency leds.
 Suitable for outdoor use due to IP44 protection grade
 Up to 4000 tubes can be connected to the controller (not included)
 Direct mains input, no costly extra power supplies needed!
 Extended life span: 50000 – 100000hours
 Low power consumption (P<12W)
 Solid aluminum holders for wall fixing included
 Perfect for use in: retail stores, commercial displays, architectural lighting, indoor and outdoor
decoration, clubs, pubs, mobile DJs, trussing, ...

BEFORE USE

 To protect the environment, try to recycle the packing material as much as possible.
 Keep this booklet in a safe place for future consultation. If you sell this unit, be sure to add this
installation manual.
 Don't use near strong magnetic fields and objects carrying high voltages.
 The electrical installation should be carried out by qualified personal.
 We strongly suggest NOT opening the unit, there are no user serviceable parts inside.
 In the event of serious operating p7roblems, stop using the unit and contact your dealer immediately.
Check the contents:
Check if the carton contains the following items:
 TUBELED™
 two aluminum holders for wall fixing
 Installation manual

SAFETY INSTRUCTIONS:

CAUTION: To reduce the risk of electric shock, do not remove the top
CAUTION
cover. No user-serviceable parts inside. Refer servicing to qualified
service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: Read instructions.
 To protect the environment, please try to recycle the packing material as much as possible.
JB SYSTEMS
®
INSTALLATION MANUAL
1/20 TUBELED™ OUTDOOR 230V
ENGLISH
 A new light effect sometimes causes some unwanted smoke and/or smell. This is normal and
disappears after some minutes.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures
when bringing it into a warm room after transport. Condense sometimes prevents the unit from
working at full performance or may even cause damages.
 Don't place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a
foreign object enters the unit, immediately disconnect the mains power.
 Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids.
 Prevent use in dusty environments and clean the unit regularly.
 Keep the unit away from children.
 Inexperienced persons should not operate this device.
 Maximum save ambient temperature is 40°C. Don't use this unit at higher ambient temperatures.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-
rigging and servicing.
 The electrical installation should be carried out by qualified personal only, according to the regulations
for electrical and mechanical safety in your country.
 Check that the available voltage is not higher than the one stated on the rear panel of the unit.
 The power cord should always be in perfect condition. Switch the unit immediately off when the power
cord is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
 Never let the power-cord come into contact with other cables!
 This fixture must be earthed to in order comply with safety regulations.
 Don't connect the unit to any dimmer pack.
 Always use an appropriate and certified safety cable when installing the unit.
 In order to prevent electric shock, do not open the cover.
 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the
same type and electrical specifications!
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 The housing and the lenses must be replaced if they are visibly damaged.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don't use the effect in the presence of persons
suffering from epilepsy.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property.
requires extensive experience! Working load limits should be respected, certified installation
materials should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-
rigging and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids.
 The device should be installed out of reach of people and outside areas where persons may walk by
or be seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the
device's weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the
unit. This secondary safety attachment should be installed in a way that no part of the installation can
drop more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 The operator has to make sure that the safety-relating and machine-technical installations are
approved by an expert before using them for the first time. The installations should be inspected
every year by a skilled person to be sure that safety is still optimal.
JB SYSTEMS
®
INSTALLATION MANUAL
Overhead rigging
2/20 TUBELED™ OUTDOOR 230V