Technical Data; Troubles Shooting - STERWINS PLM2-46B140ES.4 Manual Del Usuario

4. PARTS DESCRIPTION
Upper handle
1
Starter button
2
Locking lever
3
4 Grass catcher
5 Height adjusting lever
6 Wheel
Sideward ap
7

5. TECHNICAL DATA

Model PLM2-46B140ES.4
Engine type
B&S 575IS
Self-propelled
Yes
Engine displacement
150cm
Nominal power 2.2kW
Cutting width 46 cm
Blade type DAYE 263001465
Blade tightening torque 44~46N.m
Rated speed
2800/min
Oil tank capacity
470 cm
Fuel tank capacity
800 cm
Grass catcher capacity 60 L
Net weight 32.9 kg
Height adjustment 25-75mm, 7 adjustment
Charger model CU25-1124200 or IS12C
Charger technical data
Input : 100-240V~，50/60Hz, 0.8A
Output : 12.45V d.c., 2.0A
Battery model
IS12B
Battery technical data 10.8 V, 1.45 Ah/15.7 Wh
Measured sound pressure level 83.4dB (A) k=3 dB (A)
at operator's position
EN
Side discharge channel
8
Spark Plug
9
Battery
10
Fuel cap
11
12 Cable clamp
13 Brake control handle
Self-drive control handle
14
PLM2-52B161ES.4
B&S 775IS
Yes
161cm
2.5kW
52 cm
DAYE 263003713
44~46N.m
2800/min
600 cm
1000 cm
65 L
36.0 kg
25-75mm, 7 adjustment
CU25-1124200 or IS12C
Input : 100-240V~，50/60Hz, 0.8A
Output : 12.45V d.c., 2.0A
IS12B
10.8 V, 1.45 Ah/15.7 Wh
85.5dB (A) k=3 dB (A)
7
Measured sound power level 94.3dB (A) k= 1.80dB (A)
Guaranteed sound power level 96dB(A)
Vibration 5.62m/s² k=1.5 m/s²
In you encounter some problems with this tool, please follow these solutions.
If you cannot resolve your problem, please contact our service agent.
1. Engine does not start:
•Fill tank with fuel.
•Clean air cleaner element.
•Tighten spark plug.
•Install spark plug wire on spark plug.
•Set gap between electrodes (customer service center).
•Install new, correctly gapped plug.
•Remove air cleaner element and pull starter rope continuously until carburetor
clears itself and install air cleaner element.
2. Engine di cult to start or loses power:
•Drain fuel and clean tank. Fill tank with clean, fresh fuel.
•Clean or replace fuel tank cap.
•Clean air cleaner element.
3. Engine operates erratically:
•Install new, correctly gapped plug.
•Set gap between electrodes (customer service center).
•Clean air cleaner element.
4. Engine idles poorly:
•Clean air cleaner element.
•Remove debris from slots.
•Remove debris from cooling ns and air passages.
5. Engine skips at high speed:
•Set gap between electrodes (customer service center).
6. Engine overheats:
•Remove any debris from slots in shroud, blower housing, air passages.
7. Mower vibrates abnormally:
•Tighten blade.
•Balance blade.

6. TROUBLES SHOOTING

95.3dB (A) k= 1.83dB (A)
98dB(A)
8.04m/s² k=1.5 m/s²
6. TROUBLES SHOOTING
8
EN