Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
24. DO NOT OPERATE the tool if you are under the
influence of any drugs, alcohol or medication that
could affect your ability to use the tool properly.
25. ALWAYS operate the band saw in a well-ventilated
area and provide for proper dust removal. Use dust
collection systems whenever possible. Dust generated
from certain materials can be hazardous to your
health.
SPECIFIC SAFETY INSTRUCTIONS FOR
BAND SAWS
1.
TO AVOID INJURY from unexpected movement, make
sure the saw is on a firm, level surface, properly
secured to prevent rocking. Make sure there is
adequate space for operating. Bolt the saw to a
support surface to prevent slipping, walking, or sliding
during operation.
2.
TURN the saw OFF and unplug the saw before moving
it.
3.
USE THE CORRECT size and style of blade.
4.
USE blades rated at 2700 FPM or greater.
5.
MAKE SURE the blade teeth point down and towards
the table.
6.
BLADE GUIDES, SUPPORT BEARINGS, AND BLADE
TENSION must be properly adjusted to avoid
accidental blade contact and to minimize blade
breakage. To maximize blade support, always adjust
the upper blade guide and blade guard so that it is 1/8
inch above the work-piece.
7.
TABLE LOCK HANDLE should be tight.
8.
USE EXTRA CAUTION with large, very small or
awkward work-pieces.
9.
USE EXTRA SUPPORTS to prevent work-pieces from
sliding off the table top. Never use another person to
support the work-piece.
10. WORK-PIECES must be secured so they don't twist,
rock, or slip while being cut.
11. PLAN intricate and small work carefully to avoid
pinching the blade. Avoid awkward operation and
hand positions to prevent accidental contact with the
blade.
12. SMALL PIECES should be secured with jigs or fixtures.
Do not hand hold pieces that are so small your fingers
are under the blade guard.
13. SUPPORT round work properly (with a V-block or
clamped to the miter gauge) to prevent it from rolling
and the blade from biting.
14. CUT only one work-piece at a time. Make sure the
table is clear of everything except the work-piece and
its guides before you turn the saw on.
15. ALWAYS WATCH the saw run before each use. If
there is excessive vibration or unusual noise, stop
immediately. Turn the saw OFF. Unplug it
immediately. Do not start the saw again until the
problem has been located and corrected.
16. TO FREE any jammed material, turn the switch OFF.
Remove the switch key and unplug the saw. Wait for
all moving parts to stop before removing jammed
material.
17. DON'T LEAVE the work area until all moving parts are
stopped. To child-proof the workshop, shut OFF the
power to master switches and remove the switch key
from the band saw. Store it in a safe place, away from
children.
For your own safety, read the entire instruction manual
before operating the band saw.
1.
Wear eye protection.
2.
Do not wear gloves, necktie, or loose clothing.
3.
Make sure the saw is on a firm level surface and
properly secured.
4.
USE ONLY THE RECOMMENDED ACCESSORIES.
5.
Use extra caution with very large, very small, or
awkward work-pieces.
6.
Keep hands away from the blade at all times to
prevent accidental injury.
7.
Do not remove jammed cutoff pieces until the blade
has stopped.
8.
Maintain proper adjustment of blade tension, blade
guides and thrust bearings.
9.
Adjust upper guide to just clear the work-piece.
10. Hold the work-piece firmly against the table.
ELECTRICAL REQUIREMENTS
POWER SUPPLY AND MOTOR SPECIFICATIONS
To avoid electrical hazards, fire hazards, or damage to the
tool, use proper circuit protection. Use a separate
electrical circuit for your tools. your saw is wired at the
factory for 120V operation. Connect to a 120V, 15 Amp
circuit and use a 15 Amp time delay fuse or circuit
breaker. To avoid shock or fire, if power cord is worn or
cut, or damaged in any way, have it replaced immediately.
GROUNDING INSTRUCTIONS
This tool must be grounded while in use to protect the
operator from electrical shock.
— 5 —
WARNING
WARNING
WARNING
English
Publicidad
Tabla de contenido
Solución de problemas
