Sharpening The Mowing Blade; Sharpening Instructions; Removing And Installing The; Mowing Blade - Stihl RM 4 R Manual De Instrucciones

Ocultar thumbs Ver también para RM 4 R:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 117

12.3 Sharpening the mowing blade

If you do not have the necessary expertise
or auxiliary equipment, we recommend
that you have the blade sharpened by a
specialist dealer. Operation of the machine
is impaired in the case of an incorrectly
sharpened blade (incorrect sharpening
angle, imbalance etc.).

Sharpening instructions

● Remove the mowing blade. (
● Cool the mowing blade during
sharpening, e.g. with water.
The blade must not be allowed to
display blue colouring, as this would
reduce its cutting quality.
● Sharpen blades evenly to prevent
vibration due to imbalance.
● Observe a sharpening angle of 30°.
● Observe the wear limits (

12.4 Removing and installing the

mowing blade

Removing
● Hold mowing blade (1) and loosen
blade fastening screw (2).
● Remove blade fastening screw (2),
retaining washer (3) and mowing
blade (1).
Assembly
Risk of injury!
The mowing blade must be
replaced if notches or cracks are
detected or if it is worn. (
● Clean the blade contact surface and
blade bushing (4).
44
● Apply Loctite 243 to the thread of blade
fastening screw (2).
● Place mowing blade (1) on blade
bushing (4) as shown.
RM 4 RTP: Make sure that thrust
washer (5) is positioned correctly.
● Position retaining washer (3) as
illustrated and tighten with blade
fastening screw (2).
Tightening torque:
60 - 65 Nm
12.4)
Risk of injury!
The prescribed tightening torque
for the blade fastening screw must
be observed.
Retaining washer (3) must be
replaced each time the blade is
installed.
Blade fastening screw (2) must be
renewed each time the blade is
replaced.
12.2).
12.5 Engine

Maintenance interval:

20
See engine instruction manual.

General information:

Observe the operating and maintenance
instructions in the attached engine
instruction manual.
To achieve a long service life, it is always
particularly important to maintain a
sufficient level of oil and to change the oil
and air filter regularly.
The recommended oil change intervals as
well as information on engine oil and oil
12.2)
capacities can also be found in the engine
instruction manual.
The cooling ribs must always be kept clean
to ensure that the engine is adequately
cooled.

12.6 Storage (winter break)

Note the following points when storing the
machine for long periods (winter break):
● Clean all external parts of the machine
with care.
● Thoroughly lubricate/grease all moving
parts.
● Empty the fuel tank and carburettor
(e.g. by running empty).
● Unscrew the spark plug (see engine
instruction manual) and pour approx.
3 cm³ of engine oil into the engine via
the spark plug hole. Turn the engine
several times with the spark plug
removed (pull the recoil starter rope).
Fire hazard!
Keep the spark plug socket away
from the spark plug hole due to the
danger of ignition.
● Screw the spark plug back in (see
engine instruction manual).
● Perform an oil change (see engine
instruction manual).
● Store the machine in a dry and locked
place that is generally free of dust.
Make sure that it is out of the reach of
children.
0478 111 9943 A - EN

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Rm 4 rtRm 4 rvRm 4 rtp

Tabla de contenido